PCI-CONFIG(8) System Manager's Manual PCI-CONFIG(8)NAME
pcnet-diag - EEPROM setup and diagnostic program for ethernet cards based on the AMD PCnet/PCI series chips.
SYNOPSIS
pci-config [options]
DESCRIPTION
pci-config is a program that you can use to diagnose problems with ethernet cards
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-# <device-index>
Operate only on device <device-index>.
-a, --show_addresses
Show PCI registers
-S, --sleep
Put device to sleep (ACPI D3).
-W, --wake
Wake a sleeping device (ACPI D0 state).
-B, --bus <bus>
Show only devices on BUS.
-A, --set-addresses <addr>
Set PCI address register 1 to the <addr>.
-D, --debug
Show details of operations.
-f, --force
Override checks and perform the operation.
-u, --usage
Show a long usage message.
SEE ALSO mii-diag(8)AUTHOR
pci-config was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 PCI-CONFIG(8)
Check Out this Related Man Page
NE2K-PCI-DIAG(8) System Manager's Manual NE2K-PCI-DIAG(8)NAME
ne2k-pci-diag - EEPROM setup and diagnostic program for PCI NE2000 ethernet cards.
SYNOPSIS
ne2k-pci-diag [options]
DESCRIPTION
ne2k-pci-diag is a program that you can use to diagnose problems with PCI NE200 Enternet adapters. This include cards with RealTek
RTL8029AS, Holtak HT80232 ECON-PCI, Winbond W89c940f and VIA VT86C926 (Amazon) chips.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-h, --help
Show summary of options.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-q, --quiet
Be very unverbose.
-a, --show_all_registers
Print all registers.
-# <cardnum>
Use card number <cardnum>.
-e, --show-eeprom
Dump EEPROM contents to stdout.
-E, --emergency-rewrite
Re-write a corrupted EEPROM.
-p, --port-base <port>
Specify port to use.
-F, --new-interface <interface>
Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
100baseFx-FDX, MII and Autosense.
-H, --new-hwaddress <address>
Set card to a new hardware address.
-m, --show-mii
Dump MII management registers.
-R, --reset
Reset the transceiver.
-T, --test
Do register and SRAM test.
-w, --write-EEPROM <values>
Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!
-f, --force-detection
Try to identify the card, even if it is active.
-t, --chip-type <card>
Explicitly set the chip. To get all valid numbers, run ne2k-pci-diag with the options '-t -1'.
SEE ALSO mii-diag(8)AUTHOR
ne2k-pci-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 NE2K-PCI-DIAG(8)