myson-diag(8) [debian man page]
MYSON-DIAG(8) System Manager's Manual MYSON-DIAG(8) NAME
myson-diag - EEPROM setup and diagnostic program for ethernet cards based on the Myson MTD803 chip. SYNOPSIS
myson-diag [options] DESCRIPTION
myson-diag is a program that you can use to diagnose problems with ethernet cards based on the Myson MTD803 chip. OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -h, --help Show summary of options. -V, --version Show version of program. -v, --verbose Verbose mode. -q, --quiet Be very unverbose. -# <cardnum> Use card number <cardnum>. -a, --show_all_registers Print all registers. -e, --show-eeprom Dump EEPROM contents to stdout. -E, --emergency-rewrite Re-write a corrupted EEPROM. -p, --port-base <port> Specify port to use. -A, --Advertise <mediaype> Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD. -F, --new-interface <interface> Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx, 100baseFx-FDX, MII and Autosense. -H, --new-hwaddress <address> Set card to a new hardware address. -m, --show-mii Dump MII management registers. -R, --reset Reset the transceiver. -T, --test Do register and SRAM test. -w, --write-EEPROM <values> Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do! -f, --force-detection Try to identify the card, even if it is active. -t, --chip-type <card> Explicitly set the chip. To get all valid numbers, run myson-diag with the options '-t -1'. SEE ALSO
mii-diag(8) AUTHOR
myson-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others). February 18, 2002 MYSON-DIAG(8)
Check Out this Related Man Page
EPIC-DIAG(8) System Manager's Manual EPIC-DIAG(8) NAME
epic-diag - EEPROM setup and diagnostic program for SMC EtherPowerII ethernet cards and others. SYNOPSIS
epic-diag [options] DESCRIPTION
epic-diag is a program that you can use to diagnose problems with ethernet cards based on the SMC83C170 series EPIC/100 chip, as used on the SMC EtherPowerII boards. OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -h, --help Show summary of options. -V, --version Show version of program. -v, --verbose Verbose mode. -q, --quiet Be very unverbose. -# <cardnum> Use card number <cardnum>. -a, --show_all_registers Print all registers. -e, --show-eeprom Dump EEPROM contents to stdout. -E, --emergency-rewrite Re-write a corrupted EEPROM. -p, --port-base <port> Specify port to use. -A, --Advertise <mediaype> Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD. -F, --new-interface <interface> Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx, 100baseFx-FDX, MII and Autosense. -H, --new-hwaddress <address> Set card to a new hardware address. -m, --show-mii Dump MII management registers. -R, --reset Reset the transceiver. -T, --test Do register and SRAM test. -w, --write-EEPROM <values> Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do! -f, --force-detection Try to identify the card, even if it is active. -t, --chip-type <card> Explicitly set the chip. To get all valid numbers, run epic-diag with the options '-t -1'. SEE ALSO
mii-diag(8) AUTHOR
epic-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others). February 18, 2002 EPIC-DIAG(8)