BABELD(8) System Manager's Manual BABELD(8)
NAME
babeld - ad-hoc network routing daemon
SYNOPSIS
babeld option... [ -- ] interface...
DESCRIPTION
Babel is a loop-avoiding distance-vector routing protocol roughly based on DSDV and AODV, but with provisions for link cost estimation and
redistribution of routes from other routing protocols.
While it is optimised for wireless mesh networks, Babel will also work efficiently on wired networks.
OPTIONS
-m multicast-address
Specify the link-local multicast address to be used by the protocol. The default is ff02:0:0:0:0:0:1:6.
-p port
Specify the UDP port number to be used by the protocol. The default is 6696.
-S state-file
Set the name of the file used for preserving long-term information between invocations of the babeld daemon. If this file is
deleted, the daemon will run in passive mode for 3 minutes when it is next started (see -P below), and other hosts might initially
ignore it. The default is /var/lib/babel-state.
-h hello-interval
Specify the interval in seconds at which scheduled hello packets are sent on wireless interfaces. The default is 4 seconds.
-H wired-hello-interval
Specify the interval in seconds at which scheduled hello packets are sent on wired interfaces. The default is 4 seconds.
-z kind [,factor]
Enable diversity-sensitive routing. The value kind defines the diversity algorithm used, and can be one of 0 (no diversity), 1
(per-interface diversity with no memory), 2 (per-channel diversity with no memory), or 3 (per-channel diversity with memory). The
value factor specifies by how much the cost of non-interfering routes is multiplied, in units of 1/256; the default is 128 (i.e.
division by 2).
-k priority
Specify the priority value used when installing routes into the kernel. The default is 0.
-A priority
Allow duplicating external routes when their kernel priority is at least priority. Do not use this option unless you know what you
are doing, as it can cause persistent route flapping.
-l Use IFF_RUNNING (carrier sense) when determining interface availability.
-w Don't optimise wired links, assume all interfaces are wireless unless explicitly overridden in the configuration file.
-s Do not perform split-horizon processing on wired interfaces. Split-horizon is not performed on wireless interfaces.
-u Do not flush unfeasible (useless) routes. This is useful in order to announce more information to a front-end (see -g).
-P Run in parasitic (passive) mode. The daemon will only announce redistributed routes.
-d level
Debug level. A value of 1 requests a routing table dump at every iteration through the daemon's main loop. A value of 2 addition-
ally requests tracing every message sent or received. A value of 3 additionally dumps all interactions with the OS kernel. The
default is 0.
-g port
Listen for connections from a front-end on port port.
-t table
Use the given kernel routing table for routes inserted by babeld.
-T table
Export routes from the given kernel routing table.
-c filename
Specify the name of the configuration file. The default is /etc/babeld.conf.
-C statement
Specify a configuration statement directly on the command line.
-D Daemonise at startup.
-L logfile
Specify a file to log random ``how do you do?'' messages to. This defaults to standard error if not daemonising, and to
/var/log/babeld.log otherwise.
-I pidfile
Specify a file to write our process id to. The default is /var/run/babeld.pid.
interface...
The list of interfaces on which the protocol should operate.
CONFIGURATION FILE FORMAT
The configuration file is a sequence of lines each of which specifies either an interface or a filtering rule. Blank lines are ignored.
Comments are introduced with an octothorp ``#'' and terminate at the end of the line.
Interface configuration
An interface is configured by a single line with the following format:
interface name [parameter...]
Name is the name of the interface (something like eth0).
Each parameter specifies a parameter of the given interface. It can be one of:
wired {true|false|auto}
This specifies whether to enable optimisations specific to wired interfaces. By default, this is determined automatically unless
the -w command-line flag was specified.
link-quality {true|false|auto}
This specifies whether link quality estimation should be performed on this interface. The default is to perform link quality esti-
mation on wireless interfaces but not on wired interfaces.
split-horizon {true|false|auto}
This specifies whether to perform split-horizon processing on this interface. The default is to never perform split-horizon pro-
cessing on wireless interfaces; on wired interfaces, the default depends on the -s flag.
rxcost cost
This defines the cost of receiving frames on the given interface under ideal conditions (no packet loss); how this relates to the
actual cost used for computing metrics of routes going through this interface depends on whether link quality estimation is being
done. The default is 96 for wired interfaces, and 256 for wireless ones.
channel channel
Sets the channel for this interface. The value channel can be either an integer, or one of the strings interfering or noninterfer-
ing. The default is to autodetect the channel number for wireless interfaces, and noninterfering for wired interfaces.
faraway {true|false}
This specifies whether the network is "far away", in the sense that networks behind it don't interfere with networks in front of it.
By default, networks are not far away.
hello-interval interval
This defines the interval between hello packets sent on this interface. The default is specified with the -h and -H command-line
flags.
update-interval interval
This defines the interval between full routing table dumps sent on this interface; since Babel uses triggered updates and doesn't
count to infinity, this can be set to a fairly large value, unless significant packet loss is expected. The default is four times
the hello interval.
Filtering rules
A filtering rule is defined by a single line with the following format:
filter selector... action
Filter specifies the filter to which this entry will be added, and can be one of in, out, or redistribute.
Each selector specifies the conditions under which the given statement matches. It can be one of
ip prefix
This entry only applies to routes in the given prefix.
eq plen
This entry only applies to routes with a prefix length equal to plen.
le plen
This entry only applies to routes with a prefix length less or equal to plen.
ge plen
This entry only applies to routes with a prefix length greater or equal to plen.
neigh address
This entry only applies to routes learned from a neighbour with link-local address address.
id id This entry only applies to routes originated by a router with router-id id.
proto p
This entry only applies to kernel routes with kernel protocol number p. If neither proto nor local is specified, this entry applies
to all non-local kernel routes with a protocol different from "boot".
local This entry only applies to local addresses.
if interface
For an input filter, this specifies the interface over which the route is learned. For an output filter, this specifies the inter-
face over which this route is advertised. For a redistribute statement, this specifies the interface over which the route forwards
packets.
Action specifies the action to be taken when this entry matches. It can have one of the following values:
allow Allow this route, without changing its metric (or setting its metric to 0 in case of a redistribute filter).
deny Ignore this route.
metric value
For an input or output filter, allow this route after increasing its metric by value. For a redistribute filter, redistribute this
route with metric value.
If action is not specified, it defaults to allow.
By default, babeld redistributes all local addresses, and no other routes. In order to make sure that only the routes you specify are
redistributed, you should include the line
redistribute local deny
as the last line in your configuration file.
EXAMPLES
You can participate in a Babel network by simply running
# babeld wlan0
where wlan0 is the name of your wireless interface.
In order to gateway between multiple interfaces, just list them all on the command line:
# babeld wlan0 eth0 sit1
On an access point, you'll probably want to redistribute some external routes into Babel:
# babeld
-C 'redistribute metric 256'
wlan0
or, if you want to constrain the routes that you redistribute,
# babeld
-C 'redistribute proto 11 ip ::/0 le 64 metric 256'
-C 'redistribute proto 11 ip 0.0.0.0/0 le 24 metric 256'
wlan0
FILES
/etc/babeld.conf
The default location of the configuration file.
/var/lib/babel-state
The default location of the file storing long-term state.
/var/run/babeld.pid
The default location of the pid file.
/var/log/babeld.log
The default location of the log file.
SIGNALS
SIGUSR1
Dump Babel's routing tables to standard output or to the log file.
SIGUSR2
Check interfaces and kernel routes right now, then reopen the log file.
SECURITY
Babel is a completely insecure protocol: any attacker able to inject IP packets with a link-local source address can disrupt the protocol's
operation. This is no different from unsecured neighbour discovery or ARP.
Since Babel uses link-local IPv6 packets only, there is no need to update firewalls to allow forwarding of Babel protocol packets. If
local filtering is being done, UDP datagrams to the port used by the protocol should be allowed. As Babel uses unicast packets in some
cases, it is not enough to just allow packets destined to Babel's multicast address.
BUGS
Plenty. This is experimental software, run at your own risk.
SEE ALSO
routed(8), route6d(8), zebra(8), ahcpd(8).
AUTHOR
Juliusz Chroboczek.
BABELD(8)