MANDOS.CONF(5) Mandos Manual MANDOS.CONF(5)
NAME
mandos.conf - Configuration file for the Mandos server
SYNOPSIS
/etc/mandos/mandos.conf
DESCRIPTION
The file /etc/mandos/mandos.conf is a simple configuration file for mandos(8), and is read by it at startup. The configuration file starts
with "[DEFAULT]" on a line by itself, followed by any number of "option=value" entries, with continuations in the style of RFC 822.
"option: value" is also accepted. Note that leading whitespace is removed from values. Lines beginning with "#" or ";" are ignored and may
be used to provide comments.
OPTIONS
interface = NAME
If this is specified, the server will only announce the service and listen to requests on the specified network interface. Default is
to use all available interfaces. Note: a failure to bind to the specified interface is not considered critical, and the server will
not exit, but instead continue normally.
address = ADDRESS
If this option is used, the server will only listen to the specified IPv6 address. If a link-local address is specified, an interface
should be set, since a link-local address is only valid on a single interface. By default, the server will listen to all available
addresses. If set, this must normally be an IPv6 address; an IPv4 address can only be specified using IPv4-mapped IPv6 address syntax:
"::FFFF:192.0.2.3". (Only if IPv6 usage is disabled (see below) must this be an IPv4 address.)
port = NUMBER
If this option is used, the server will bind to that port. By default, the server will listen to an arbitrary port given by the
operating system.
debug = { 1 | yes | true | on | 0 | no | false | off }
If the server is run in debug mode, it will run in the foreground and print a lot of debugging information. The default is to not run
in debug mode.
priority = STRING
GnuTLS priority string for the TLS handshake. The default is "SECURE256:!CTYPE-X.509:+CTYPE-OPENPGP". See gnutls_priority_init(3) for
the syntax. Warning: changing this may make the TLS handshake fail, making server-client communication impossible.
servicename = NAME
Zeroconf service name. The default is "Mandos". This only needs to be changed if for some reason is would be necessary to run more than
one server on the same host. This would not normally be useful. If there are name collisions on the same network, the newer server will
automatically rename itself to "Mandos #2", and so on; therefore, this option is not needed in that case.
use_dbus = { 1 | yes | true | on | 0 | no | false | off }
This option controls whether the server will provide a D-Bus system bus interface. The default is to provide such an interface.
use_ipv6 = { 1 | yes | true | on | 0 | no | false | off }
This option controls whether the server will use IPv6 sockets and addresses. The default is to use IPv6. This option should never
normally be turned off, even in IPv4-only environments. This is because mandos-client(8mandos) will normally use IPv6 link-local
addresses, and will not be able to find or connect to the server if this option is turned off. Only advanced users should consider
changing this option.
restore = { 1 | yes | true | on | 0 | no | false | off }
This option controls whether the server will restore its state from the last time it ran. Default is to restore last state.
statedir = DIRECTORY
Directory to save (and restore) state in. Default is "/var/lib/mandos".
socket = NUMBER
If this option is used, the server will not create a new network socket, but will instead use the supplied file descriptor. By default,
the server will create a new network socket.
FILES
The file described here is /etc/mandos/mandos.conf
BUGS
The [DEFAULT] is necessary because the Python built-in module ConfigParser requires it.
EXAMPLE
No options are actually required:
[DEFAULT]
An example using all the options:
[DEFAULT]
# A configuration example
interface = eth0
address = fe80::aede:48ff:fe71:f6f2
port = 1025
debug = true
priority = SECURE256:!CTYPE-X.509:+CTYPE-OPENPGP
servicename = Daena
use_dbus = False
use_ipv6 = True
restore = True
statedir = /var/lib/mandos
SEE ALSO
intro(8mandos), gnutls_priority_init(3), mandos(8), mandos-clients.conf(5)
RFC 4291: IP Version 6 Addressing Architecture
Section 2.2: Text Representation of Addresses
Section 2.5.5.2: IPv4-Mapped IPv6 Address
Section 2.5.6, Link-Local IPv6 Unicast Addresses
The clients use IPv6 link-local addresses, which are immediately usable since a link-local addresses is automatically assigned to a
network interface when it is brought up.
Zeroconf[1]
Zeroconf is the network protocol standard used by clients for finding the Mandos server on the local network.
COPYRIGHT
Copyright (C) 2008-2009, 2011-2012 Teddy Hogeborn, Bjorn Pahlsson
This manual page is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published
by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
This manual page is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/.
NOTES
1. Zeroconf
http://www.zeroconf.org/
Mandos 1.5.5 2012-05-26 MANDOS.CONF(5)