REMAKE(1) LOCAL USER COMMANDS REMAKE(1)
NAME
remake - A patched GNU make with a debuger, better tracing and error reporting
SYNOPSIS
remake [ -f makefile ] [ options ] ... [ targets ] ...
WARNING
This man page is an extract of the documentation of GNU remake ( make + debugger). It is updated only occasionally, because the GNU
project does not use nroff. For complete, current documentation, refer to the Info file make.info and mdb.info which are made from the
Texinfo source files make.texi. and mdb.texi The latter describes debugger behavior.
DESCRIPTION
The purpose of the make utility is to determine automatically which pieces of a large program need to be recompiled, and issue the commands
to recompile them. See documentation on GNU make for more information.
However in this patched version we add a debugger which can be entered either initially (option -X or --debugger) or on an error (--debug-
ger=error). We also add better tracing facilities (option -x) and we report postion information better. When an error is encountered more
information is given automatically.
See also the home <http://bashdb.sf.net/remake> page for more information.
OPTIONS
-b, -m
These options are ignored for compatibility with other versions of make.
-B, --always-make
Unconditionally make all targets.
-C dir, --directory=dir
Change to directory dir before reading the makefiles or doing anything else. If multiple -C options are specified, each is inter-
preted relative to the previous one: -C / -C etc is equivalent to -C /etc. This is typically used with recursive invocations of make.
-d Print debugging information in addition to normal processing. The debugging information says which files are being considered for
remaking, which file-times are being compared and with what results, which files actually need to be remade, which implicit rules are
considered and which are applied---everything interesting about how make decides what to do.
--debug[=FLAGS]
Print debugging information in addition to normal processing. If the FLAGS are omitted, then the behavior is the same as if -d was
specified. FLAGS may be a for all debugging output (same as using -d), b for basic debugging, v for more verbose basic debugging, i
for showing implicit rules, j for details on invocation of commands, and m for debugging while remaking makefiles.
--debugger[=FLAGS]
Enter the debugger. If the FLAGS are omitted, then the behavior is the same as if --debugger=full was specified. FLAGS may be a for
all debugging output (same as using -d), error the debugger is only entered on encountering an error. It may be possible to quit the
debugger and continue processing. So the overall effect could be like the " --keep-going" switch. fatal the debugger is only entered
on encountering a fatal error. preread the debugger is entered after command-line options are parsed but before andy Makefiles have
been read. It also sets step-tracing mode. preaction Enters the debugger after command-line options are parsed and after Makefiles
have been read, but before any action is performed. It also sets step-tracing mode. full for basic debugging,
-e, --environment-overrides
Give variables taken from the environment precedence over variables from makefiles.
+-f file, --file=file, --makefile=FILE
Use file as a makefile.
-i, --ignore-errors
Ignore all errors in commands executed to remake files.
-I dir, --include-dir=dir
Specifies a directory dir to search for included makefiles. If several -I options are used to specify several directories, the direc-
tories are searched in the order specified. Unlike the arguments to other flags of make, directories given with -I flags may come
directly after the flag: -Idir is allowed, as well as -I dir. This syntax is allowed for compatibility with the C preprocessor's -I
flag.
-j [jobs], --jobs[=jobs]
Specifies the number of jobs (commands) to run simultaneously. If there is more than one -j option, the last one is effective. If
the -j option is given without an argument, remake will not limit the number of jobs that can run simultaneously.
-k, --keep-going
Continue as much as possible after an error. While the target that failed, and those that depend on it, cannot be remade, the other
dependencies of these targets can be processed all the same.
-l [load], --load-average[=load]
Specifies that no new jobs (commands) should be started if there are others jobs running and the load average is at least load (a
floating-point number). With no argument, removes a previous load limit.
-L, --check-symlink-times
Use the latest mtime between symlinks and target.
-n, --just-print, --dry-run, --recon
Print the commands that would be executed, but do not execute them.
-o file, --old-file=file, --assume-old=file
Do not remake the file file even if it is older than its dependencies, and do not remake anything on account of changes in file.
Essentially the file is treated as very old and its rules are ignored.
-p, --print-data-base
Print the data base (rules and variable values) that results from reading the makefiles; then execute as usual or as otherwise speci-
fied. This also prints the version information given by the -v switch (see below). To print the data base without trying to remake
any files, use remake -p -f/dev/null.
-q, --question
``Question mode''. Do not run any commands, or print anything; just return an exit status that is zero if the specified targets are
already up to date, nonzero otherwise.
-r, --no-builtin-rules
Eliminate use of the built-in implicit rules. Also clear out the default list of suffixes for suffix rules.
-R, --no-builtin-variables
Don't define any built-in variables.
-s, --silent, --quiet
Silent operation; do not print the commands as they are executed.
-S, --no-keep-going, --stop
Cancel the effect of the -k option. This is never necessary except in a recursive make where -k might be inherited from the top-level
make via MAKEFLAGS or if you set -k in MAKEFLAGS in your environment.
-t, --touch
Touch files (mark them up to date without really changing them) instead of running their commands. This is used to pretend that the
commands were done, in order to fool future invocations of remake.
-v, --version
Print the version of the make program plus a copyright, a list of authors and a notice that there is no warranty.
-w, --print-directory
Print a message containing the working directory before and after other processing. This may be useful for tracking down errors from
complicated nests of recursive make commands.
--no-print-directory
Turn off -w, even if it was turned on implicitly.
-W file, --what-if=file, --new-file=file, --assume-new=file
Pretend that the target file has just been modified. When used with the -n flag, this shows you what would happen if you were to mod-
ify that file. Without -n, it is almost the same as running a touch command on the given file before running make, except that the
modification time is changed only in the imagination of make.
-x, --trace [=FLAGS]
Sets up execution tracing. If FLAGS are omitted, then the behavior is the same as if " --trace=full" was specified. full normal trac-
ing read show in addition status on reading in makefiles full the most verbose tracing.
--warn-undefined-variables
Warn when an undefined variable is referenced.
EXIT STATUS
GNU remake exits with a status of zero if all makefiles were successfully parsed and no targets that were built failed. A status of one
will be returned if the -q flag was used and make determines that a target needs to be rebuilt. A status of two will be returned if any
errors were encountered. An exit status of 77 can be given when quitting from the debugger out of a recursive invocation.
SEE ALSO
The GNU Remake Manual and the The GNU Remake Debugger Manual
BUGS
See the chapter `Problems and Bugs' in The GNU Remake Manual.
AUTHOR
This manual page contributed by Dennis Morse of Stanford University. It has been reworked by Roland McGrath. Further updates contributed
by Mike Frysinger and Rocky Bernstein.
GNU
25 February 2007 REMAKE(1)