Ipv6 on hpux

8 More Discussions You Might Find Interesting

1. Solaris

Solaris 10 IPv6

Hello Dears , please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface . Thanks in...

2. IP Networking

IPv6 Problems

I am trying to setup an IPv6 network. I modified the interfaces file: /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback iface etho0 inet static address 2620:7:a000::1 netmask 64 gateway ::ffff:c0a8:101 ...

3. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your...

4. HP-UX

pwage-hpux-T for Trusted HPUX servers

I'm sharing this in case anybody needs it. Modified from the original solaris pwage script. This modified hpux script will check /etc/password file on hpux trusted systems search /tcb and grep the required u_succhg field. Calculate days to expiry and notify users via email. original solaris...

5. SuSE

Linux and IPv6

Hi gurus, In a few month, we must enable IPv6 on our Linux Server! Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files? Could Linux run simultaneous IPv4 and IPv6? Thanks in advance for our help our ideas? Best regards, nm

6. Shell Programming and Scripting

Need Script to Use CPUs on a HPUX server to simulate Workload Manager on HPUX.

I am running HPUX and using WLM (workload manager). I want to write a script to fork CPUs to basically take CPUs from other servers to show that the communication is working and CPU licensing is working. Basically, I want to build a script that will use up CPU on a server. Any ideas?

7. AIX

IPv6 on AIX

Hi Every1, I want to configure IPv6 on AIX and want to communicate between IPv4 machine IP and IPv6 machine. Is it possible?

8. IP Networking

IPv6 testbed

Hello guyz.. did some of u have implement or making a testbed for IPv6? if yes, can u attached the procedures and standard guidelines because i really need for my proposal.. thanx..

LEARN ABOUT HPUX

pppoesd.conf

pppoesd.conf(4) 					     Kernel Interfaces Manual						   pppoesd.conf(4)

NAME

       pppoesd.conf - PPPoE (Point to Point Protocol over Ethernet) server configuration file

DESCRIPTION

       is the configuration file for the daemon.  This file is read by to initialize the server.  The default file is You can use this file to set
       parameters for each network interface used by during PPPoE sessions.  Each entry in the file is of the following format:

       Each entry in the configuration file is separated by a blank line.  Blank lines and lines that begin with are ignored.

   Parameters
       contains the following parameters:

       Specify the name of the service that the server can offer to the client.
			 A value of implies that the server is ready to offer any service to the client.

       Specify the name of the access concentrator from which you wish to make
			 services available.

       Specify a tag used by the client to uniquely associate an access
			 concentrator's response (PADO or PADS) to a particular client request (PADI or PADR).

       Specify the number of times
			 tries to retransmit either a PADI or PADR packet when an access concentrator does not respond to the client's request.

       Specify the timeout value in seconds.
			 waits for this duration to receive either a PADO or PADS packet before retransmitting a PADI/PADR  packet.   The  default
			 value is 15 seconds.

       Specify the command-line options of
			 See pppd(1) for more information.

   Sample pppoesd.conf File
	   [ lan4 ]
	   service=any
	   acname=gatt3
	   ac_cookie=1
	   #host_unique=0
	   timeout=1200
	   #retry-number=3
	   local-ipv4-address=1.2.3.4
	   ipv4-address-pool=5.6.7.8 - 5.6.7.101
	   pppd-options=mru 1492 debug 11
	   # Following entries are related to PPPoEv6
	   local-ipv6-identifier=::9
	   ipv6-identifier-pool=::10 - ::100

AUTHOR

       was developed by Hewlett-Packard.

FILES

       PPPoE server daemon
       PPPoE relay
       PPPoE client
       PPP daemon

SEE ALSO

       pppd(1), pppoec(1), pppoerd(1M), pppoesd(1M).

																   pppoesd.conf(4)

HP-UX