External GPU issue

 
Thread Tools Search this Thread
Special Forums Hardware External GPU issue
# 1  
Old 10-18-2011
External GPU issue

Dear all,

I set up a external Gforce GPU using the PE4H (Pcie passive adapter) from HWTOOLS.NET.

I'm able to add and remove the device doing

Quote:
echo 1 > /sys/bus/pci/rescan
and
Quote:
echo 1 > /sys/bus/pci/devices/0000\:01\:00.0/remove
echo 1 > /sys/bus/pci/devices/0000\:01\:00.1/remove
The point is the kernel does not initialized the device correctly.
Here is what dmesg gives after the scan:

Quote:
pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00ffffff]
pci 0000:01:00.0: reg 14: [mem 0x00000000-0x07ffffff 64bit pref]
pci 0000:01:00.0: reg 1c: [mem 0x00000000-0x01ffffff 64bit pref]
pci 0000:01:00.0: reg 24: [io 0x0000-0x007f]
pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0007ffff pref]
pci 0000:01:00.1: reg 10: [mem 0x00000000-0x00003fff]
i915 0000:00:02.0: BAR 6: [??? 0 flags 0x2] has bogus alignment
pcieport 0000:00:01.0: BAR 9: can't assign mem pref (size 0xc000000)
pcieport 0000:00:01.0: BAR 7: assigned [io 0x3000-0x3fff]
pci 0000:01:00.0: BAR 1: can't assign mem pref (size 0x8000000)
pci 0000:01:00.0: BAR 3: can't assign mem pref (size 0x2000000)
pci 0000:01:00.0: BAR 0: can't assign mem (size 0x1000000)
pci 0000:01:00.0: BAR 6: assigned [mem 0xfe500000-0xfe57ffff pref]
pci 0000:01:00.1: BAR 0: assigned [mem 0xfe580000-0xfe583fff]
pci 0000:01:00.1: BAR 0: set to [mem 0xfe580000-0xfe583fff] (PCI address [0xfe580000-0xfe583fff]
pci 0000:01:00.0: BAR 5: assigned [io 0x3000-0x307f]
pci 0000:01:00.0: BAR 5: set to [io 0x3000-0x307f] (PCI address [0x3000-0x307f]
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
nvidia 0000:01:00.0: enabling device (0000 -> 0001)
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:
NVRM: BAR0 is 0M @ 0x0 (PCI:0000:01:00.0)
NVRM: The system BIOS may have misconfigured your GPU.
nvidia: probe of 0000:01:00.0 failed with error -1
NVRM: The NVIDIA probe routine failed for 1 device(s).
NVRM: None of the NVIDIA graphics adapters were initialized!
lspci -t gives

Quote:

-[0000:00]-+-00.0 Intel Corporation 4 Series Chipset DRAM Controller
+-01.0-[01]--+-00.0 nVidia Corporation GF110 [Geforce GTX 580]
| \-00.1 nVidia Corporation GF110 High Definition Audio Controller
+-02.0 Intel Corporation 4 Series Chipset Integrated Graphics Controller
+-02.1 Intel Corporation 4 Series Chipset Integrated Graphics Controller
+-03.0 Intel Corporation 4 Series Chipset HECI Controller
+-03.2 Intel Corporation 4 Series Chipset PT IDER Controller
+-03.3 Intel Corporation 4 Series Chipset Serial KT Controller
+-19.0 Intel Corporation 82567LM-3 Gigabit Network Connection
+-1a.0 Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #4
+-1a.1 Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #5
+-1a.2 Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #6
+-1a.7 Intel Corporation 82801JD/DO (ICH10 Family) USB2 EHCI Controller #2
+-1b.0 Intel Corporation 82801JD/DO (ICH10 Family) HD Audio Controller
+-1c.0-[02]--
+-1c.1-[03]--
+-1d.0 Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #1
+-1d.1 Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #2
+-1d.2 Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #3
+-1d.7 Intel Corporation 82801JD/DO (ICH10 Family) USB2 EHCI Controller #1
+-1e.0-[04]--
+-1f.0 Intel Corporation 82801JDO (ICH10DO) LPC Interface Controller
+-1f.2 Intel Corporation 82801 SATA RAID Controller
\-1f.3 Intel Corporation 82801JD/DO (ICH10 Family) SMBus Controller
and lspci -vvv this

Quote:

01:00.0 3D controller: nVidia Corporation GF110 [Geforce GTX 580] (rev a1)
Subsystem: Device 196e:086a
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 1: Memory at <unassigned> (64-bit, prefetchable)
Region 3: Memory at <unassigned> (64-bit, prefetchable)
Region 5: I/O ports at 3000 [size=128]
[virtual] Expansion ROM at fe500000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x2, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [b4] Vendor Specific Information <?>
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information <?>
Kernel modules: nvidia, nouveau, nvidiafb

01:00.1 Audio device: nVidia Corporation GF110 High Definition Audio Controller (rev a1)
Subsystem: Device 196e:086a
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 0
Region 0: Memory at fe580000 (32-bit, non-prefetchable) [disabled] [size=16K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x2, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

So, it would be great if an expert could help me to figure out what's going wrong here.
Is there any chance to solve it?

I thank you in advance,

Éric.
# 2  
Old 10-18-2011
It might help to know what operating system you're using...
# 3  
Old 10-18-2011
I'm running Slackware64 13.1
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Linux

Vfio passtrough gpu, a question about hdmi

The situation videocard n°1 Nvidia Ge-force(used on host linux) videocard n°2 Ati radeon(used on guest windows 7) host is Slackware 14.2,kernel 4.18.15 I had set vfio to pass a ati card to windows7 guest Configure /etc/modprobe.d/vfio.conf options vfio-pci... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies

2. Hardware

How disabling GPU?

Hi All I'm find out a way to disable the DGD: AMD Radeon HD 7470M on my Ubutu 16.04.2 LTS because radeon open source module is not capable to support this GPU and consequence the boot is very slow. I have tried serveral way with pci-stub.ids in the grub menu but not work. In general how... (11 Replies)
Discussion started by: _Fabio_79
11 Replies

3. Hardware

Cooler GPU

In one of our computers a Zotac GPU was installed (Zotac GeForce GTX 780 3GB AMP! to be exact) and the processor remained an Intel Core i7 2600. For the processor a new after-market cooler was installed and for the GPU also, together with fans on all case grids. Initially the temperatures as... (4 Replies)
Discussion started by: figaro
4 Replies

4. Red Hat

External HDD Issue

Hello everyone ! I just installed Red Hat 6.4 and when i plug in my external HDD firstly i can see the files and after 5 seconds all dissapears. What causes to this and ways to fix it ? Thanks in advance ! (1 Reply)
Discussion started by: djqbert
1 Replies

5. UNIX for Advanced & Expert Users

GPU and CUDA

Hi , i want begin programming using CUDA which enviroment can i get .I don't have desktop to buy GPU graphics card. what should to do to get CUDA enviroment. i'm thinking to buy desktop has this card or laptop (1 Reply)
Discussion started by: Scotch
1 Replies

6. UNIX for Advanced & Expert Users

opmn service listening to external connections - issue

Hello Gentlemen, Its been a looong time I have posted here. I need a clarification. We started up the OPMN service (for Oracle App server) on Linux box. The service was supposed to listen on port 6005. The service started up and was listening to 6005 but looks like it was listening only to... (7 Replies)
Discussion started by: ranj@chn
7 Replies

7. UNIX for Advanced & Expert Users

external DVD-ROM drive issue whether it is working or not?on HP rp74000

old clunker - rp74000 How to diag the external DVD-ROM drives issue whether it is working or not? on HP 9000 server rp7400 Please help me > I needed to install HP 11i v1 using external DVD-ROM drive on HP 9000 server rp7400. While boot in CO> “search” command is not showing DVD-ROM device... (1 Reply)
Discussion started by: tpuser
1 Replies

8. HP-UX

External DVD-ROM drive issue whether it is working or not? on HP rp7400

Please help me > How to diag the external DVD-ROM drive issue whether it is working or not? on HP 9000 server rp7400 I needed to install HP 11i v1 using external DVD-ROM drive on HP 9000 server rp7400. While boot in CO> “search” command is not showing DVD-ROM device only showing all disks >... (0 Replies)
Discussion started by: tpuser
0 Replies

9. Solaris

Tracing the GPU usage

Hello, Can give me some tips to trace the GPU usage on a solaris8 update7 box? I try to understand why a Cadcam app is so slow on my Solaris box compared to a win$ box. I guess it comes from the poor graphic card I have but i would like to emphasize it. My bench is 150sec long on a Solaris... (0 Replies)
Discussion started by: solea
0 Replies
Login or Register to Ask a Question