Jeg forsøger at installere en HP StorageWorks DAT40 Tape drev på SC0 5.0.7. Båndet drev er ikke funktionel.

Når jeg kører # sconf-mod dette er, hvad jeg får;

Sdsk ad160 0 0 0 0
Sdsk ad160 0 0 1 0
STP ad160 0 0 3 0

Men når jeg køre # hwconfig-h det er, hvad jeg får;

enheden adresse vec DMA kommentar
\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d \u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d
kerne - - - rel \u003d 3.2v5.0.7 kid \u003d 2003-02-18
CPU - - - enhed \u003d 1 familie \u003d 15 type \u003d Intel Xeon
cpuid - - - enhed \u003d 1 vend \u003d GenuineIntel tfms \u003d 0:15:2:9 (11)
fpu - 13 - enhed \u003d 1 type \u003d 80387-kompatibel
PCI 0xcf8-0xcff - - am \u003d 1 sc \u003d 0 busser \u003d 3
PnP - - - nodes \u003d 0
ur - - - type \u003d TSC/2.392032383Ghz
seriel 0x3f8-0x3ff 4 - enhed \u003d 0 type \u003d Standard nports \u003d 1 base \u003d 0 16550A/16
konsol - - - enhed \u003d vga type \u003d 0 num \u003d 12 scoansi \u003d 1 rulle \u003d 50
adapter 0xd800-0xd8ff 11 - type \u003d ad160 ha \u003d 0 slot \u003d 0 bus \u003d 0 id \u003d 7 FTS \u003d sto
adapter 0xdc00-0xdcff 3 - type \u003d ad160 ha \u003d 1 slot \u003d 0 bus \u003d 0 id \u003d 7 FTS \u003d sto
floppy 0x3f2-0x3f7 6 2 enhed \u003d 0 type \u003d 135ds18
Udi - - - UDI miljø
adapter - - - ha \u003d 0 type \u003d usb_msto UDI SCSI HBA
adapter 0x170-0x177 15 - type \u003d IDE ctlr \u003d sekundære dvr \u003d wd
bcme0 - 3 - chip \u003d BCM5703 mem \u003d FCD00000 PHY \u003d BCM5703 DDR \u003d 00:10: 18:06:49:56
CD-ROM - - - type \u003d IDE enhed \u003d 0 ctlr \u003d sek cfg \u003d mst dvr \u003d Srom-> wd
disk - - - type \u003d S ha \u003d 0 id \u003d 0 Lun \u003d 0 bus \u003d 0 HT \u003d ad160 enhed \u003d 0
Sdsk - - - cyls \u003d 4.427 HDS \u003d 255 sek \u003d 63 enhed \u003d 0 FTS \u003d stdb
Sdsk-0 - - - Vnd \u003d Seagate PRD \u003d ST336753LW Rev \u003d DX10
usb_ohci - 5 - PCI bus \u003d 0 dev \u003d 15 funk \u003d 2

Jeg bruger Lone tar som backup-software, og det genkender ikke båndet, når jeg foretager en scanning.

Du skal installere bånddrevet første hjælp
mkdev tape

Følg anvisningerne for at installere.

Jeg var i stand til at løse problemet geninstallation af SCSI-kortet føreren. Tak for din hjælp ...