how to round up a memory address(memory alignment problem) - High Level Programming

nj302 · #1 09-18-2005

Hi, I try to marshal a unsigned int and a char * into a buffer, and then unmarshal them later to get them out. I need to put the char * in the front and unsigned int at the end of the buffer. However, my system always give me "BUS ERROR". I am using Sun Sparcs Sloris 2.10.

My code to marshal the data:

unsigned dev = 111;
unsigned inode = 222;

int s_docname = strlen(docname) + 1;
int s_key = s_docname + sizeof(unsigned) * 2;

keybuf = malloc(s_key);
memset(keybuf, 0, s_key);
memcpy(keybuf, docname, s_docname);
memcpy(keybuf + s_docname, &(dev), sizeof(unsigned));
memcpy(keybuf + s_docname + sizeof(unsigned), &(inode),
sizeof(unsigned));

My code to unmarshal the data:
char * docname = (char *)key.data;
int s_docname = strlen(docname) + 1;
dev =*((unsigned *)((char *)key.data + s_docname));
inode = *((unsigned *)((char *)key.data + s_docname +
sizeof(unsigned)));

I can print the dev and inode out in dbx debugger by typing the same
code, but running the program always have the BUS error.

I realize this is a problems of memory alignement. s_docname has byte granularity, somehow I need to "round up" my s_docname by some suitable calculation. But I really don't know how to? Help is appreciated.

blowtorch · #2 09-18-2005

Here is a possible alternate solution (I really haven't understood the problem very well - I may be completely off here)

Code:

#include<stdlib.h>
#include<string.h>

int main(argc,argv)
int argc;
char *argv[];
{
        unsigned int dev=111,inode=222;
        char docname[]="/tmp/test";
        char *keybuf;
        int s_docname,s_key;

        s_docname=strlen(docname);
        s_key=s_docname+(sizeof(unsigned)*2)+1;
        keybuf=(char*)malloc(s_key);
        if(!keybuf) {
                perror("error in malloc!");
                exit(-1);
        }
        sprintf(keybuf,"%s %u %u",docname,dev,inode);
        fprintf(stdout,"%s\n",keybuf);
        docname[0]=0;
        dev=0;
        inode=0;
        fprintf(stdout,"doc: %s, dev: %d, inode: %d\n",docname,dev,inode);
        sscanf(keybuf,"%s %u %u",docname,&dev,&inode);
        fprintf(stdout,"post sscanf\n");
        fprintf(stdout,"doc: %s, dev: %d, inode: %d\n",docname,dev,inode);
        exit(0);
}

nj302 · #3 09-21-2005

Still I got same bus error. The problem is that the dev is not at the address where keybuff + s_docname is

Some processors are not able to load an integer, unsigned etc, from an address which is not a multiple of the size of that integer. For 4-byte integers, the address it is loaded from, looking at the lowest two bit only, must be 00. It is called 4-byte alignment.

I need to "round up" my s_docname by some suitable calculation, leaving what is called 'padding' between docname and dev.

I need some advice on how to round this up. Thanks a lot.

Perderabo · #4 09-21-2005

Don't dereference the pointer in place. Since you memcpy'ed it in, memcpy it back out. Then deference it.

nj302 · #5 09-21-2005

Sorry, but I don't understand what exactly you mean?

Perderabo · #6 09-21-2005

Replace:
dev =*((unsigned *)((char *)key.data + s_docname));
with:
memcpy(dev, keybuf + s_docname, sizeof(unsigned));
and make a similar for inode.

nj302 · #7 09-21-2005

Problem solved. Thank you very much, Perderabo!

More UNIX and Linux Forum Topics You Might Find Helpful
Thread	Thread Starter	Forum	Replies	Last Post
How to find Total and Free Physical Memory and Logical Memory in SOLARIS 9	0ktalmagik	Filesystems, Disks and Memory	2	07-21-2008 04:38 AM
How can I get memory usage or anything that show memory used from sar file?	panithat	HP-UX	1	03-31-2008 09:26 AM
Memory Alignment Problem on Sun Sparcs	nj302	SUN Solaris	1	09-21-2005 04:07 PM
Shared memory shortage but lots of unused memory	cjcamaro	UNIX for Advanced & Expert Users	1	10-13-2004 02:10 PM
Total Memory/Swap Memory	ghe1	Filesystems, Disks and Memory	4	04-01-2002 07:33 AM

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode