06-27-2005
thanks for the reply
i believe lsof command uses the following file
/dev/kmem
on the stranger part
i tried on server1 - it was working fine and i could all the information that i needed
and when i tried it on server2 - it was showing permission denied
i checked the permissions for the file on either of the servers and it was the same
could you please explain why its show different behaviour.
I do need one more clarification.
Ports indicating LISTEN status are the ones picked by the process and opened to accept connections right?
There is no list of acceptable ports which could hereby be opened and connected.
I think i am making myself clear. Kindly revert if i had to explain my question in detail.
Thanks
9 More Discussions You Might Find Interesting
1. Cybersecurity
/* Linux Slackware */
Nmap shows the following ports open on the gateway.
21/tcp ftp
22/tcp ssh
23/tcp telnet
25/tcp smtp
37/tcp time
80/tcp http
113/tcp auth
515/tcp printer
587/tcp submission
1024/tcp kdm
6000/tcp x11
-------------------------------
i would like to close as... (10 Replies)
Discussion started by: LowOrderBit
10 Replies
2. Linux
how can i open ports i need in red hat server vs root access ? (7 Replies)
Discussion started by: Sirius
7 Replies
3. Shell Programming and Scripting
Hello, i need a script (bash type maybe?..), which would check open ports on 127.0.0.1 and then compare open ports with "registered/allowed" port list and try to kill the program who uses unregistered ports. It would be great that script would be started lets say every 5 or 10 minutes.
You see i... (2 Replies)
Discussion started by: MorchiuS
2 Replies
4. AIX
Hi Every body,
What is the command on AIX 5.2 that can be used to get all open ports? (2 Replies)
Discussion started by: aldowsary
2 Replies
5. Solaris
Hello,
I have a number of Solaris 8 Sun servers that have open ports that I cannot identify. I see some with 1013-1023 (which are reserved ports according to the IANA. Lsof does not identify these. I rebooted the server and they went off, but this morning I saw they were all back on again. Any... (1 Reply)
Discussion started by: csgonan
1 Replies
6. IP Networking
I'm fairly new to networking and am trying to figure our network out, as I was recently assigned to be network administrator where I work. I was trying to get utorrent to work but am not having success in figuring out what's blocking my ports. As of now, I'm getting connected from a mikrotik... (11 Replies)
Discussion started by: brandonros
11 Replies
7. Solaris
hi guys,
may i know the exact steps to open a port in solaris.i have some rough idea - which is adding the port number in /etc/services.
but i am not sure the correct conventions, steps or any other steps.
kindly advise.thanks guys ! (1 Reply)
Discussion started by: cromohawk
1 Replies
8. UNIX for Dummies Questions & Answers
just a quick question:
a. whats the simplest command to check open port and the corresponding services?
example:
bash-2.05# netstat -an | grep LISTEN
*.199 *.* 0 0 49152 0 LISTEN
*.8989 *.* 0 0 49152 ... (1 Reply)
Discussion started by: lhareigh890
1 Replies
9. IP Networking
Hi,
I have read some forum theads about the open and close ports. some points are clear and it is not working on my machine or something am i missing?
I have commented out a port /etc/services, one application uses
then when i use the telnet <hostname> <port_blocked> it shows connected..... (1 Reply)
Discussion started by: balamv
1 Replies
LEARN ABOUT ULTRIX
ntp.conf
ntp.conf(5) File Formats Manual ntp.conf(5)
Name
ntp.conf - Network Time Protocol configuration file
Description
The file is the configuration file for the Network Time Protocol (NTP) daemon, This file must be configured on your system before running
Any host names that you specify in the file must have an entry in the file, or an entry in the master database, if the database is being
served to your system by BIND/Hesiod or Yellow Pages.
The file has four entry formats:
trusting no
This entry guarantees that your system synchronizes only to the NTP servers identified in the peer and server entries specified. Dig-
ital recommends that all systems include the entry.
peer server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system may also provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP servers should be configured with entries.
server server
This entry identifies server as one of the NTP servers that your system trusts, and from which your system will accept time synchro-
nization. Your system can not provide time synchronization to this server. Servers can be identified by host name or internet
address.
NTP clients should be configured with entries.
peer /dev/null LOCL 1 -5 local
This entry identifies your system as a local reference clock. A local reference clock is the most accurate system clock available at
your site. If you receive time synchronization from the Internet NTP service, you should not include this entry on any of your sys-
tems. At most, one system in a set of nodes running should be identified as a local reference clock.
A host which specifies this entry should not specify any or entries.
Examples
This is a sample configuration file for an NTP client which receives time synchronization from the NTP servers: and Lines beginning with a
number sign (#) are comments.
#
# NTP Configuration File
# This file is mandatory for the ntpd daemon
#
#
#
# ** A L L **
#
# "trusting no" prevents this host from synchronizing
# to any host that is not listed below. It is recommended
# that all hosts include the line "trusting no".
#
trusting no
#
#
# ** S E R V E R **
#
# If you are configuring a server, use "peer" entries to
# synchronize to other NTP servers. For example, server1,
# server2, and server3.
#
#peer server1
#peer server2
#peer server3
#
#
#
#
# ** C L I E N T **
#
# If you are configuring a client, use "server" entries to
# synchronize to NTP servers. For example, server1, server2,
# and server3.
#
server server1
server server2
server server3
#
#
#
# ** L O C A L R E F E R E N C E C L O C K **
#
# If you are configuring a local reference clock, include the
# following entry and the "trusting no" entry ONLY.
#
#peer /dev/null LOCL 1 -5 local
#
See Also
ntp(1), ntpd(8), ntpdc(8)
RFC 1129--Internet time synchronization: The Network Time Protocol
Introduction to Networking and Distributed System Services
ntp.conf(5)