Sponsored Content
Full Discussion: 2540-M2 Firmware
Operating Systems Solaris 2540-M2 Firmware Post 302988063 by rbatte1 on Tuesday 20th of December 2016 06:49:24 AM
Old 12-20-2016
Try this link for a start.

For me, a good document is listed at position 4, "Sun StorageTek Common Array Manager Software Release Notes" but sequence may vary.



Robin
 

10 More Discussions You Might Find Interesting

1. Solaris

One StorageTek 6140 vs Two (2) 2540 's?

We're moving our production 3510FC to development, so we need to replace the production 3510FC. The 6140 is nice, but pricey. Here's the question: Would two 2540's (RAID 10) be 'faster' than one 3510? (RAID 10) and faster than one 6140 (RAID 10)? One StoregeTek 6140 (16x72GB 15k rpm fc-al... (12 Replies)
Discussion started by: buddhavelvet
12 Replies

2. Solaris

fdisk -l doesn't see one 2540 array, can see other arrays though

I can't seem to get my host to see a 2540 array. I have 3 arrays right now. (2) 2540's.. let's call them 2540A and 2540B and (1) 6140. 2540A and the 6140 are configured and mounted on the same linux host. For the life of me, I cannot get the other problem-child 2540B to be recognized by the... (6 Replies)
Discussion started by: buddhavelvet
6 Replies

3. Solaris

Sun StorageTek 2540 - shutdown matrix

Hi, I have a simple question on how to correctly disable the matrix? Looking for the Common Array Manager and I do not see this option... Thank for help (3 Replies)
Discussion started by: bieszczaders
3 Replies

4. Solaris

Storagetek 2540

Hi peeps, Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables. Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Discussion started by: callmebob
1 Replies

5. Hardware

Storagetek 2540

Hello all ! I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server. I... (2 Replies)
Discussion started by: acorradi
2 Replies

6. Hardware

StorageTek 2540 battery failed

Hi all, My Sun StorageTek 2540 have redundant batteries, but a battery was failed. # /opt/SUNWstkcam/bin/sscs list -d MyStorage1 fru Name FRU Alarm State Status Revision Unique Id -------------------------- ----------- --------... (2 Replies)
Discussion started by: buyantugs
2 Replies

7. Hardware

Storagetek 2540

Hi Guys and Gals, Wionder if you could help me, got a problem with a controller on a storagetek 2540, dead when fully powered up but if you reboot, it is ok for a couple of seconds (and you can ping it). Then once the array is fully up, it goes faulty and is un-pingable. Had anyone... (4 Replies)
Discussion started by: callmebob
4 Replies

8. Hardware

2540 firmware update

Hi Guys and Gals, does anyone know how to update the firmware on the drives in a storagetek 2540? Thanks in advance Rgrds Martin (0 Replies)
Discussion started by: callmebob
0 Replies

9. Solaris

StorageTek 2540 SAN array

Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun. We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
Discussion started by: edison303
6 Replies

10. Solaris

Lost out-of-band communication with 2540 Array

Hello Dears, My server hots cannot contacted my array disk 2540 by using out-of-band Ethernet Cable. The Controller Ethernet port is off , I replace the ethernet cable but not OK I reboot the server and the Array disk 2540 but Not OK. Please somebody know how to solve this issue? ... (1 Reply)
Discussion started by: ghislino
1 Replies
HXCOPY(1)							  HTML-XML-utils							 HXCOPY(1)

NAME
hxcopy - copy an HTML file and update its relative links SYNOPSIS
hxcopy [ -i old-URL ] [ -o new-URL ] [ file-or-URL [ file-or-URL ] ] DESCRIPTION
The hxcopy command copies its first argument to its second argument, while updating relative links. The input is assumed to be HTML or XHTML and may be slightly reformatted in the process. If the second argument is omitted, hxcopy writes to standard output. In this case the option -o is required. If the first argument is also omitted, hxcopy reads from standard input. In this case the option -i is required. OPTIONS
The following options are supported: -i old-URL For the purposes of updating relative links, act as if old-URL is the location from which the input is copied. If this option is omitted, the actual location of the first argument is used for calculating relative links. -o new-URL For the purposed of updating relative links, act as if new-URL is the location to which the input is copied. If this option is omitted, the actual location of the second argument is used for calculating relative links. ENVIRONMENT
To use a proxy to retrieve remote files, set the environment variables http_proxy and ftp_proxy. E.g., http_proxy="http://localhost:8080/" BUGS
Unlike the last argument of cp(1), the last argument of hxcopy must be a file, not a directory. The second argument must be a local file. Writing to a URL is not yet implemented. To work around this, replace hxcopy file.html http://example.org/file.html by hxcopy -o http://example.org/file.html file.html tmp.html and then upload tmp.html to the given URL with some other command, such as curl(1). The first argument, however, may be a URL. hxcopy will download the given file. (Currently only HTTP is supported.) EXAMPLE
Assume the HTML file foo.html contains a relative link to "../bar.html". Here are some examples of commands: hxcopy foo.html bar/foo.html The file foo.html is copied to ../bar/foo.html and the relative link to "../bar.html" becomes "../../bar.html". hxcopy foo.html ../foo.html The file foo.html is copied to ../foo.html and the relative link to "../bar.html" is rewritten as "bar.html". hxcopy -i http://my.org/dir1/foo.html -o http://my.org/foo.html file1.html file2.html The file file1.html is copied to file2.html and the relative link to "../bar.html" is rewritten as "bar.html". A command like this may be useful to update files that are later uploaded to a server. SEE ALSO
cp(1), curl(1), hxwls(1) 6.x 9 Dec 2008 HXCOPY(1)
All times are GMT -4. The time now is 11:38 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy