HP C8000 with HP-UX 10.20 Post: 302984851

Sponsored Content

Operating Systems HP-UX HP C8000 with HP-UX 10.20 Post 302984851 by vbe on Tuesday 1st of November 2016 10:49:22 AM

11-01-2016

Moderator

What I see is that aC8000 is a pure 64 bit machine, and I dont remember if you had a 10.20 in 64 bits, as I always had 10.20 in 32 bit even for first 64 bits compatible box like K3XX series, then at the time of 10.20 there were no PCI slots nor could I remember of ultraSCSI the boxes had FW-SCSI2 perhaps and HSC expansion.., I would not say its impossible, but I would start by looking for the last HP 10.20 archive ( dec 2001 I think ) and look what firmware upgrades wer given, then look if any extra patches ( firware were released ) you could use to be compatible, and of course look in you can run in 32bit as it was possible with the first generations of PA8000 but here you have a PA 8800....

vbe

View Public Profile for vbe

Find all posts by vbe

2 More Discussions You Might Find Interesting

1. HP-UX

HP UX 11i and HP C8000

Hey, i want install HP UX 11i on HP C8000. When i start the C8000 i get a prompt. On this Prompt i write BOot P1 P1 is my DVD-ROM (IDE). I get the Message "ERROR: Not a boot path". When i write SEArch the Prompt said: P0 scsiA.6 HP73.4MAT3073NP P1 ide.1 ...

2. HP-UX

Help needed HP UX 11.11i new install on C8000 Desktop messaging system error CAN'T FIX

Hi, I have a HP UX C8000 box , have installed 11.11i from 4 x cds numerous times to try to get a functioning Network or to try and get rid of this error on start up, after new install and 1st startup I get an error "The desktop messaging system could not be started" and then advice about...

LEARN ABOUT OSF1

malo

MALO(4) 						   BSD Kernel Interfaces Manual 						   MALO(4)

NAME

     malo -- Marvell Libertas IEEE 802.11b/g wireless network driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device malo
	   device pci
	   device wlan
	   device firmware

     Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):

	   if_malo_load="YES"

DESCRIPTION

     The malo driver provides support for Marvell Libertas 88W8335 based PCI and Cardbus network adapters.  malo supports station and monitor mode
     operation.  Only one virtual interface may be configured at any time.  For more information on configuring this device, see ifconfig(8).

     This driver requires the malofw firmware kernel module be installed before it will work.  The firmware files are not publicly available.  A
     port of the firmware can be found at:

	   http://weongyo.org/project/malo/malo-firmware-1.4.tar.gz

     The firmware kernel module can be installed by extracting the archive and running 'make install clean' in the malo-firmware-1.4 directory.

HARDWARE

     The following cards are among those supported by the malo driver:

	   Card 		  Chip	     Bus	Standard
	   Netgear WG311v3	  88W8335    PCI	b/g
	   Tenda TWL542P	  88W8335    PCI	b/g
	   U-Khan UW-2054i	  88W8335    PCI	b/g

EXAMPLES

     Join an existing BSS network (i.e., connect to an access point):

	   ifconfig wlan create wlandev malo0 inet 192.168.0.20 
	       netmask 0xffffff00

     Join a specific BSS network with network name ``my_net'':

	   ifconfig wlan create wlandev malo0 ssid my_net up

     Join a specific BSS network with 64-bit WEP encryption:

	   ifconfig wlan create wlandev malo0 ssid my_net 
		   wepmode on wepkey 0x1234567890 weptxkey 1 up

SEE ALSO

     cardbus(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8)

HISTORY

     The malo device driver first appeared in FreeBSD 7.1.

BSD
								 October 21, 2009							       BSD