Sponsored Content
Full Discussion: SCO 5.0.7 Configuration
Operating Systems SCO SCO 5.0.7 Configuration Post 302964601 by Kanthi Kiran on Saturday 16th of January 2016 11:54:40 AM
Old 01-16-2016
SCO 5.0.7 Configuration

Hi,
I am really new to the forum and for SCO as well. I have a burning situation here to know how to configure below list of hardware into SCO 5.0.7!!
  • EQUINOX 990209-1 ELS 16 PORT TERMINAL SERVER and
  • Seagate DAT Scorpion 24 - Tape drive ( 12 GB / ) DDS-3 SCSI

Can Any One Please Help Me in Detailed !!

---------- Post updated at 11:54 AM ---------- Previous update was at 11:52 AM ----------

We Have installed SCO 5.0.7 on ESXi 6.0 and we need to configured above hardware !! Can any one help me please ???
 

7 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Internet Configuration in SCO 5.05

Hi, I'm trying to configure SCO's internet manager for access to the internet. However, when I start the config program, my desktop turns black & white (unless I minimize communicator's window -- then it turns back to normal). I type in the user id and password and it looks as if the... (1 Reply)
Discussion started by: gseyforth
1 Replies

2. UNIX for Dummies Questions & Answers

Configuration management tool in SCO UNIXWARE 7.1.3

Hi all, :confused: I want to know about the configuration management tool that is used in SCO UNIXWARE 7.1.3. Please refer some sites where i could get the details. Thanks in advance kavitha (2 Replies)
Discussion started by: kavithadass
2 Replies

3. SCO

SCO Unix Network Configuration

Hello Guys, We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
2 Replies

4. SCO

raid 1 configuration in sco open unix

Dear Team , how i can configure raid 1 (mirroring) using ide hdd in sco open unix 5 i have two 80gb identical hdd (same make/model) thanx (0 Replies)
Discussion started by: sudhir69
0 Replies

5. SCO

Alias in SCO network configuration

We have many remote servers that are running different versions of the SCO operating system. The current server inventory includes the usage of SCO 3.2v5.0.5 3.2v5.0.6 and 3.2v5.0.7. Recently, there have been some ongoing problems when a re-boot is done with some of these remote servers.... (0 Replies)
Discussion started by: dclary
0 Replies

6. UNIX for Dummies Questions & Answers

SCO Printer configuration file

Hello, I am working on Servers running SCO OpenServer 5 and I tend to setup a lot of Servers. I am wondering if mkdev -lp to create printers has a file that I can just copy and paste from an exisiting Server to a new (upgrade) server. I can do this with the hosts and resolv.conf files. ... (1 Reply)
Discussion started by: ewerezak
1 Replies

7. SCO

SCO 5.5 remote login configuration

Sir, i have a sco 5.5 installed server and 6 clients connected through pci specialix card and printing working fine in these all terminals. 7 and 8 ports are free now, i need to setup another terminal for login on through 7 or 8 port for remote login. i connect a external modem using 25 pin male... (3 Replies)
Discussion started by: Aneesh Kumar.T
3 Replies
RESCAN-SCSI-BUS.SH(1)						   User Commands					     RESCAN-SCSI-BUS.SH(1)

NAME
rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting SYNOPSIS
rescan-scsi-bus.sh [options] [host [host ...]] OPTIONS
-a, --alltargets scan all targets, not just currently existing [default: disabled] -d enable debug [default: 0] -l activates scanning for LUNs 0--7 [default: 0] -L NUM activates scanning for LUNs 0--NUM [default: 0] -w, --wide scan for target device IDs 0--15 [default: 0--7] -c enables scanning of channels 0 1 [default: 0 / all detected ones] -r, --remove enables removing of devices [default: disabled] -f, --flush flush failed multipath devices [default: disabled] -i, --issue-lip issue a FibreChannel LIP reset [default: disabled] -u, --update look for existing disks that have been remapped -s, --resize look for resized disks and reload associated multipath devices, if applicable --forcerescan rescan existing devices --forceremove remove and readd every device (DANGEROUS) --nooptscan don't stop looking for LUNs is 0 is not found --color use coloured prefixes OLD/NEW/DEL --hosts=LIST scan only host(s) in LIST --channels=LIST scan only channel(s) in LIST --ids=LIST scan only target ID(s) in LIST --luns=LIST scan only lun(s) in LIST --sync, --nosync issue a sync / no sync [default: sync if remove] --attachpq3 tell kernel to attach sg to LUN 0 that reports PQ=3 --reportlun2 tell kernel to try REPORT_LUN even on SCSI2 devices --largelun tell kernel to support LUNs > 7 even on SCSI2 devs --sparselun tell kernel to support sparse LUN numbering Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended). LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.) SEE ALSO
rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi sg3_utils Homepage: http://sg.danny.cz/sg rescan-scsi-bus.sh 1.57 leden 2014 RESCAN-SCSI-BUS.SH(1)
All times are GMT -4. The time now is 01:52 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy