I've just started using awk. At the moment I only know how to grab fields. So the fancy things you're doing, I have no idea. This works though, thank's a bunch!
Moderator's Comments:
Please use code tags
Last edited by Scott; 07-06-2013 at 11:53 PM..
Reason: Code tags
Hi, I'm very new to scripting.
grep $s $filename | awk '{print $2}' | cut -c 1-8
How can I optimize this using a single awk?
I tried:
awk '/$s/ {print $2}' $filename | cut -c 1-8
However didn't work, I think the awk is not recognizing $s and the verbal is something else. (6 Replies)
I have grep MHz psrinfo-v.out
it gives
The i386 processor operates at 3000 MHz,
The i386 processor operates at 3000 MHz,
The i386 processor operates at 3000 MHz,
The i386 processor operates at 3000 MHz,
how to get instead of these 4 lines:
CPU speed: 3000 MHz
i.e. CPU... (3 Replies)
Hi Guys,
I need to set the value of $7 to zero in case $7 is NULL. I've tried the below command but doesn't work. Any ideas. thanks guys.
MEM=`ps v $PPID| grep -i db2 | grep -v grep| awk '{ if ( $7 ~ " " ) { print 0 } else { print $7}}' `
Harby. (4 Replies)
This may just be a lack of experience talking, but I always assumed that when possible it was better to use a commands built in abilities rather than to pipe to a bunch of commands. I wrote a (very simple) script a while back that was meant to pull out a certain error code, and report back what... (4 Replies)
Hello,
I trying to extract text that is surrounded by xml-tags. I tried this
cat tst.xml | egrep "<SERVER>.*</SERVER>" |sed -e "s/<SERVER>\(.*\)<\/SERVER>/\1/"|tr "|" " "
which works perfect, if the start-tag and the end-tag are in the same line, e.g.:
<tag1>Hello Linux-Users</tag1>
... (5 Replies)
Hi,
I have a number of files containing the information below.
"""""
Fundallinfo
6.3950 14.9715 14.0482
"""""
I would like to grep for Fundallinfo and use it to read the next line? I ideally would like to read the three numbers that follow in the next line and... (2 Replies)
Hi ,
I have a file where i have modifed certain things compared to original file . The difference of the original file and modified file is as follows.
# diff mir_lex.c.modified mir_lex.c.orig
3209c3209
< if(yy_current_buffer -> yy_is_our_buffer == 0) {
---
>... (5 Replies)
Hi Guys.
I am trying to count occurances of patterns(occurance can be anywhere in file2) from file1 in file2.
file1 is
god
god
pod
rod
file2 is
iamgod
iamgod
podrod
123rod456
output should be
god 2
god 2
pod 1
rod 2
I am not good at awk but i figured out this command.it doesnt... (7 Replies)
Discussion started by: ahfze
7 Replies
LEARN ABOUT DEBIAN
ifscheme
IFSCHEME(8) Commands IFSCHEME(8)NAME
ifscheme - scheme control for network interfaces
SYNOPSIS
ifscheme [-v] [[-s] newscheme]
mapping <interface> script ifscheme-mapping
DESCRIPTION
ifscheme allows you to change network configuraton schemes or query the current scheme. It integrates with the ifup(8) command and inter-
faces(5). For example, you might use this program to configure a "home" scheme and a "work" scheme for a network device on a laptop. When
you move between home and work, a simple command can reconfigure your networking.
If you run the program with no parameters, it will tell what the current network scheme is.
The ifscheme-mapping utility is used to tell the ifup and ifdown utilities about the current scheme.
OPTIONS -v
--verbose
Run in verbose mode. This is passed in to the ifup and ifdown programs as well.
-l
--list list all schemes available/defined in /etc/network/interfaces.
newscheme
-s newscheme
--scheme newscheme
Change to a new network configuration scheme. When the scheme is changed, network interfaces that were using the old scheme will be
taken down and brought back up to use the new configuration scheme. -s or --scheme are mandatory if newscheme begins with a -.
CONFIGURATION
To make the program do anything useful when a scheme is selected, you must edit /etc/network/interfaces to add a mapping for the interface
(or interfaces) that can be controlled on a per-scheme basis. Suppose you want to control eth0 in this way. You might have an existing eth0
configuraton in there, such as:
auto eth0
iface eth0 inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
To change this so you can chose between static routing and dhcp, replace it with the following (it helps to ifdown the interface first).
auto eth0
mapping eth0
script ifscheme-mapping
iface eth0-home inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
iface eth0-work inet dhcp
Now if you run "ifscheme home" and ifup the interface, you'll get the eth0-home configuration stanza. If you run "ifscheme work", it will
be changed to the eth0-work stanza. You can add additional stanzas as desired, but the label must always be of the form <hardware inter-
face>-<scheme name>.
If you have a second interface (perhaps a wireless network card on eth1), you can duplicate the above for that interface, changing the eth0
and the configuration details as appropriate, but remember to add an iface stanza for every scheme name for the second interface.
FILES
/etc/network/interfaces
the interfaces definition file
/etc/network/run/scheme
the current scheme
/etc/network/run/ifstate
a record of the current state of the interfaces, managed by ifup and ifdown
BUGS
All schemed interfaces will have the same scheme.
Any schemed interface which does not have an entry for the current scheme and is not configured when the scheme is changed will not be suc-
cessfully configured when it is brought up.
SEE ALSO interfaces(5)ifup(8)ifdown(8)DISTRIBUTION
Redistribution is subject to the GNU public license.
AUTHORS
Joey Hess <joey@kitenet.net>, Peter Wilson <pwilson@cs.hmc.edu>
IFSCHEME(8)