I checked with my other servers which were running fine they have the same output.
Also here are the results for ndd -get
I don't know if it helps but it's set to auto_neg with the 1000 speeds enabled.
I am trying to set an interface to 100/Full, but the command I use are getting rejected. I think it is the last argument, but I don't know how to find the correct values.
I am trying to use the following script, but change hme to le .
echo "Setting hme interface 1: 100mb/full-duplex..."
... (2 Replies)
Hi Guys,
I need help with ndd.
I was going through network FAQ but i have more questions then answers regarding ndd.
#ndd -set /dev/hme instance 0
#ndd -set /dev/hme adv_100fdx_cap 1
#ndd -set /dev/hme adv_100hdx_cap 0
#ndd -set /dev/hme adv_10fdx_cap 0
#ndd -set /dev/hme adv_10hdx_cap 0... (2 Replies)
Hello Gurus
I would like to know more about ndd commands related to ethernet(NIC) like how to set link_status, link_speed & link_mode as I know how to check these value. And I also would like to know how to make these setting permanents after reboot as I know that these setting will vanish... (5 Replies)
Hi,
I would like to know whether there is any config file that i can refer to for the result of 'ndd -get /dev/tcp tcp_time_wait_interval'?
When i man 'ndd', there is one statement which is -> Each driver chooses which parameters to make visible using ndd. Does it answering my question above... (3 Replies)
Solaris 10 server (SunOS 5.10 Generic_137137_09)
I have a services file configured in /etc in there windows clients connect to my server on port 6034-6037
when I do the following
netstat | grep TestServices
it pulls all the connections active for those ports
so right now I have 10 clients... (3 Replies)
Following command was set up in startup script on Solaris 8 servers - improved network transfers of files from one server to the another (doubled transfer speed).
ndd -set /dev/tcp tcp_host_param '10.140.20.10 sendspace 279600 recvspace 279600 timestamp 1'
Now they are getting a new server... (15 Replies)
Hello,
I recently upgraded our system from Solaris 8 to 10. It seems couple of binaries crashed in the new server Solaris 10. Before digging too much on it , from theory it sounds like any binary that is built on Solaris 8 (using gmake) is supposed to be compatible with Solaris 10 , right ?
... (1 Reply)
Hi,
I'm having issues with sendmail when I try to send host to host mail. I've had to change the "my official domain name" line to mycompany.com to get the mails through the external spam filter, when a mail was sent with hostname.mycompany.com it was blocked. I had to change the Dj macro... (0 Replies)
Hi,
Recently, I had to disable autoneg in one of my servers having ixgbe1 interface. While using below command I got "Permission denied" error:
ndd -set /dev/ixgbe1 adv_autoneg_cap 0
On investigating further I found that adv_autoneg_cap is showing as read-only parameter. Although it is... (1 Reply)
Discussion started by: rochitsharma
1 Replies
LEARN ABOUT REDHAT
ndd
ndd(1M) System Administration Commands ndd(1M)NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)