Is it possible to create a Mirror with zfs ??
I'm experimented user with Solstice Disk suite.
Or Sun Volume manager or veritas volume manager.
But, i would like switch from Disksuite to Zfs.
All my mirrored disks. (1 Reply)
I've looked a little but haven't found a solid answer, assuming there is one.
What's better, hardware mirroring or ZFS mirroring? Common practice for us was to use the raid controllers on the Sun x86 servers. Now we've been using ZFS mirroring since U6. Any performance difference? Any other... (3 Replies)
I'd like to finish setting up this system and then move the secondary or primary disk to another system that is the exact same hardware.
I've done things like this in the past with ufs and disk suite mirroring just fine. But I have yet to do it with a zfs root pool mirror.
Are there any... (1 Reply)
hello folks,
I have a 300GB ROOTVG volume groups with one filesystem /backup having 200GB allocated space
Now, I cannot alt disk clone or mirrorvg this hdisk with another smaller disk. The disk size has to be 300GB; I tried alt disk clone and mirrorvg , it doesn't work. you cannot copy LVs as... (9 Replies)
Hi everyone,
I am doing housekeeping of my Solaris 11 for zfs snapshot to reduce the snapshot size. I have already cleared the / file system, however the rpool size still not reduced.
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 6.9G ... (2 Replies)
Hi,
I am unable to understand that, in one of my servers while
df -kh
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 11G 29G 29% /
Even the Root FS filled on 40gb and system becomes unstable.
it is showing... (4 Replies)
Hi,
I have this fresh installation of Solaris 11.3 sparc.
I have two zfs pools both using two disks in mirroring mode, both are online.
I want to move /system/zones, currently rpool/VARSHARE/zones, from rpool to the other zfs pool so my zones don't consume space on the disks allocated to... (1 Reply)
I have a 240GB disk as rpool. I have installed Solaris 11.3 to a partition which is 110GB. Now I have another 130GB which is unallocated. I want to use that additional space as a temporary folder to be shared between Solaris and Linux. The additional space had no /dev/dsk/c2t4... entry so I used... (8 Replies)
Discussion started by: kebabbert
8 Replies
LEARN ABOUT DEBIAN
bbdb-areacode-split
BBDB-AREACODE-SPLIT.PL(1) General Commands Manual BBDB-AREACODE-SPLIT.PL(1)NAME
bbdb-areacode-split - Looks for phone numbers in your .bbdb
SYNOPSIS
bbdb-areacode-split <old-code> <new-code> <exchanges-file> [bbdb]
DESCRIPTION
Looks for phone numbers in your .bbdb with a particular area code and one of a set of exchanges and changes the area code. The old and new
area codes are specified on the command line, as is the location of a file that contains the exchanges that are being changed. (The format
of that file is very loose. Every three digit sequence will be used.)
This manual page was written for the Debian distribution because the original program does not have a manual page. Instead, it has docu-
mentation in the GNU Info format; see below.
SEE ALSO bbdb-cid(1), bbdb-unlazy-lock(1). bbdb-srv(1).
The bbdb is fully documented by The insidious Big Brother Database for mail and news, available via the Infonode bbdb
AUTHOR
This manual page was written by Joerg Jaspert (JJ) <joerg@goliathbbs.dnsalias.net>, for the Debian GNU/Linux system (but may be used by
others).
March 31, 2002 BBDB-AREACODE-SPLIT.PL(1)