I have Solaris-10 (release-7) box without any non global zone. I have a very critical change after couple of days from application side. For safer side, we want to keep few level of backups just in case of faliure. This server is having three pool
I will create a lu copy with lucreate. Apart from it, can I pull one disk out of the server while I shut down the server ? Just in case of failure of application, I will pull out disk_0 and insert disk_1 (which was pulled out) and bring server up. Does it make sense ?
Also, I am not sure if lu will conflict with this procedure. And if I follow it, do I need to run some commands to break zfs rpool mirror ?
Last edited by solaris_1977; 06-13-2013 at 11:17 PM..
Is it possible to create a Mirror with zfs ??
I'm experimented user with Solstice Disk suite.
Or Sun Volume manager or veritas volume manager.
But, i would like switch from Disksuite to Zfs.
All my mirrored disks. (1 Reply)
I've looked a little but haven't found a solid answer, assuming there is one.
What's better, hardware mirroring or ZFS mirroring? Common practice for us was to use the raid controllers on the Sun x86 servers. Now we've been using ZFS mirroring since U6. Any performance difference? Any other... (3 Replies)
I'd like to finish setting up this system and then move the secondary or primary disk to another system that is the exact same hardware.
I've done things like this in the past with ufs and disk suite mirroring just fine. But I have yet to do it with a zfs root pool mirror.
Are there any... (1 Reply)
hello folks,
I have a 300GB ROOTVG volume groups with one filesystem /backup having 200GB allocated space
Now, I cannot alt disk clone or mirrorvg this hdisk with another smaller disk. The disk size has to be 300GB; I tried alt disk clone and mirrorvg , it doesn't work. you cannot copy LVs as... (9 Replies)
Hi everyone,
I am doing housekeeping of my Solaris 11 for zfs snapshot to reduce the snapshot size. I have already cleared the / file system, however the rpool size still not reduced.
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 6.9G ... (2 Replies)
Hi,
I am unable to understand that, in one of my servers while
df -kh
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 11G 29G 29% /
Even the Root FS filled on 40gb and system becomes unstable.
it is showing... (4 Replies)
Hi,
I have this fresh installation of Solaris 11.3 sparc.
I have two zfs pools both using two disks in mirroring mode, both are online.
I want to move /system/zones, currently rpool/VARSHARE/zones, from rpool to the other zfs pool so my zones don't consume space on the disks allocated to... (1 Reply)
I have a 240GB disk as rpool. I have installed Solaris 11.3 to a partition which is 110GB. Now I have another 130GB which is unallocated. I want to use that additional space as a temporary folder to be shared between Solaris and Linux. The additional space had no /dev/dsk/c2t4... entry so I used... (8 Replies)
Discussion started by: kebabbert
8 Replies
LEARN ABOUT OSF1
named-xfer
named-xfer(8) System Manager's Manual named-xfer(8)NAME
named-xfer - Pulls BIND zones from another server
SYNOPSIS
/usr/sbin/named-xfer -z zone_to_transfer -f db_file -s serial_no [-d debug_level] [-l debug_log_file] [-t trace_file] [-p port] [-S]
servers...
OPTIONS
Specifies the name of the BIND zone for the named-xfer daemon to transfer, for example, dec.com. This option is required to pull a zone.
Specifies the name of the file into which the pulled zone information is placed. This option is required to pull a zone. Specifies the
current serial number of the SOA record for the zone zone_to_transfer. If serial_no is set to 0, the zone is always pulled. This option is
required to pull a zone. Sets the debug level and determines the amount of debug information to be displayed. Specifies the file that
will contain any debug messages from the zone pull. Specifies the file that will contain a trace from the zone pull. Specifies the port
that will be used instead of the default name server port listed in /etc/services. Performs a restricted transfer of only the SOA, NS
records and glue A records for the zone. The SOA record is not loaded by named, but is used to determine when to verify the NS records.
See named(8) for more information. Specifies a list of Internet addresses, in dotted-quad format, from which to pull a zone. If the first
host cannot be reached, the named transfer daemon tries to pull the zone from the next host listed.
DESCRIPTION
The named transfer daemon, /usr/sbin/named-xfer, is a server that is usually run by the named daemon, /usr/sbin/named, but it can also be
run manually with the given arguments. The named transfer daemon runs on a BIND secondary server and pulls BIND zones from a primary
server. This daemon is not run by default, nor can it be started up from inetd(8).
SEE ALSO
Commands: named(8)
Files: resolver(4), services(4)named-xfer(8)