03-15-2013
I saw the page about dladm, but for some reasons, some of those sub-commands are not available on my server (i.e. rename-link, show-phys, ...)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
3. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX for Advanced & Expert Users
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Discussion started by: sadosan83
3 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT HPUX
show_link
show link(1m) show link(1m)
NAME
show link - Displays attribute information about the specified soft link
SYNOPSIS
cdscp show link link-name [attribute-name] [with attribute-name = attribute-value]
ARGUMENTS
The full name of a specific soft link. The last simple name can contain wildcard characters. The name of a particular attribute; see
Description for valid attribute names. The value of a particular attribute.
DESCRIPTION
The show link command displays the names and values of the attributes specified in attribute-name. You can use a combination of attributes
in any sequence in a single command. Use a space to separate multiple attributes. You can use a with attribute-name = attribute-value
clause to limit output only to soft links whose attributes have values equal to the specified values. A space must precede and follow the
= (equals sign). If you do not supply any attributes, the command displays all attributes and their values. The following is a description
of soft link attributes: Specifies the creation timestamp (CTS) of this soft link Specifies the full name of the directory, object entry,
or other soft link to which the soft link points Specifies a timeout value after which the soft link is either checked or deleted Specifies
the timestamp of the most recent update to an attribute of the soft link
Privilege Required
You must have read permission to the soft link. If you specify a wildcard soft link name, you also need read permission to the directory
that stores the soft link.
NOTE
This command is replaced at Revision 1.1 by the dcecp command and may not be provided in future releases of DCE.
EXAMPLE
The following command displays the current values of all the attributes associated with the soft link /.:/sales/region1. cdscp> show link
/.:/sales/region1
SHOW
SOFTLINK /.../abc.com/sales/region1
AT 1991-10-15-15:54:40
CDS_CTS = 1991-10-15-19:54:35.00000003/08-00-2b-1c-8f-1f
CDS_UTS = 1991-10-15-19:54:35.00000006/08-00-2b-1c-8f-1f
CDS_LinkTarget = /.../abc.com/sales/service
SHOW
SOFTLINK /.../abc.com/sales/region1
AT 1991-10-15-15:54:41
CDS_CTS = 1991-10-15-19:54:36.00000077/08-00-2b-1c-8f-1f
CDS_UTS = 1991-10-15-19:54:36.00000009/08-00-2b-1c-8f-1f
CDS_LinkTarget = /.../abc.com/sales/software
CDS_LinkTimeout = :
Expiration = 1991-10-15-00:00:00.0
Extension = +1-00:00:00.000
RELATED INFORMATION
Commands: create link(1m), delete link(1m), list link(1m), remove link(1m), set link(1m)
show link(1m)