03-15-2013
I saw the page about dladm, but for some reasons, some of those sub-commands are not available on my server (i.e. rename-link, show-phys, ...)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
3. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX for Advanced & Expert Users
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Discussion started by: sadosan83
3 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT OPENSOLARIS
wpad
wpad(1M) System Administration Commands wpad(1M)
NAME
wpad - WPA and WPA2 protocol daemon
SYNOPSIS
/usr/lib/inet/wpad [-i interface] [-k pre_shared_key_name]
DESCRIPTION
The wpad daemon provides common client functionality for the WiFi Protected Access (WPA) versions 1 and 2, as defined by IEEE802.11i stan-
dard. WPA was created by the WiFi Alliance, an industry trade group. WPA implements the majority of the IEEE 802.11i standard, and was
intended as an intermediate measure to take the place of Wired Equivalent Privacy (WEP) while 802.11i was prepared. WPA2 implements the
full standard.
wpad provides the following WPA/IEEE 802.11i features:
o WPA-PSK ("WPA-Personal")
o Key management for CCMP, TKIP, WEP104, WEP40
Stop and start the wpad daemon using dladm(1M). Use:
# dladm connect-wifi
...to start the wpad daemon. Use:
# dladm disconnect-wifi
...to stop the daemon.
OPTIONS
The following options are supported:
-i interface
Specify a WiFi Link interface to start the wpad daemon.
-k pre_shared_key_name
Specify the pre-shared key used for the WiFi Link.
EXAMPLES
Example 1 Starting the wpad Daemon on Specific WiFi Link
To create the WPA key psk, enter the following command:
# dladm create-secobj -c wpa psk
To use key psk to connect to ESSID wlan on link ath0, enter the following command:
# dladm connect-wifi -k psk -e wlan ath0
Example 2 Stopping the wpad Daemon on Specific WiFi Link
To stop the daemon on the link ath0, enter:
# dladm disconnect-wifi ath0
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWwpau, SUNWwpar |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1), dladm(1M), svcadm(1M), attributes(5), smf(5)
NOTES
The wpad service is managed by the service management facility, smf(5), under the service identifier:
svc:/network/wpa:<link>
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
SunOS 5.11 11 Mar 2008 wpad(1M)