03-07-2013
i have done it with iscsi. and, yes, i assume the no_resdrve setting is also needed. been nearly 18 months since i have played with ha.
have fun.
ps, if working with systemmirror 7.x remember that the ha interfaces will multicast for caa. if you have a lot of systems in a vlan they may be affected..
10 More Discussions You Might Find Interesting
1. AIX
Hello,
I would like to know if anyone has faced this problem. Whenever there is a duplicate IP address, HACMP goes down infact HACMP ( PowerHA ) takes the whole system down.
Does anyone know how to solve this problem ? (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
3. AIX
I am planning for building a new database server using AIX 6.1 and Oracle 11.2 using ASM.
As i have learned starting with Oracle 11.2 ASM can only be used in conjunction with Clusterware, which is Oracles HA-software. As is the companies policy we do intend to use PowerHA as HA-solution instead... (1 Reply)
Discussion started by: bakunin
1 Replies
4. AIX
Hello!
I have this infraestructure:
- 1 POWER7 with single VIOS on Site A.
- 1 POWER6 with single VIOS on Site B.
- 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A.
- 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB.
- 1 Storage DS4700 on Site A.
- 1... (8 Replies)
Discussion started by: enzote
8 Replies
5. AIX
Hello AIX GURU's
Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server?
my questions are:
1.
Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar?
or
2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Hello,
AIX 6.1 TL7 SP6
POwerHA 6.1 SP10
I was experimenting with new hacmp build. It's 3-node cluster build on AIX 6.1 lpars. It contains Ethernet and diskhb networks. Shared vg disk is SAN disk. Two nodes see disk using vscsi, third node sees disk using npiv. Application is db2 server.
... (4 Replies)
Discussion started by: vilius
4 Replies
8. AIX
hello
ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415
work with dmx4 EMC storgae.
after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine :
hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies
9. AIX
I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp.
Please share me steps for adding vxvm diskgroup to hacmp. (6 Replies)
Discussion started by: sunnybee
6 Replies
10. AIX
Hi All,
As per the IBM upgrade/support matrix
IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix
we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ...
1 ) Bring down the cluster
2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LEARN ABOUT REDHAT
vconfig
VCONFIG(8) System Manager's Manual VCONFIG(8)
NAME
vconfig - VLAN (802.1q) configuration program.
SYNOPSIS
vconfig [lots of long options]
DESCRIPTION
The vconfig program allows you to create and remove vlan-devices on a vlan enabled kernel. Vlan-devices are virtual ethernet devices which
represents the virtual lans on the physical lan.
OPTIONS
add [interface-name] [vlan-id]
Creates a vlan-device on [interface-name]. The resulting vlan-device will be called according to the nameing convention set.
rem [vlan-device]
Removes the named vlan-device.
set_flag [vlan-device] 0 | 1
When 1, ethernet header reorders are turned on. Dumping the device will appear as a common ethernet device without vlans. When
0(default) however, ethernet headers are not reordered, which results in vlan tagged packets when dumping the device. Usually the
default gives no problems, but some packet filtering programs might have problems with it.
set_egress_map [vlan-device] [skb-priority] [vlan-qos]
This flags that outbound packets with a particular skb-priority should be tagged with the particular vlan priority vlan-qos. The
default vlan priority is 0.
set_ingress_map [vlan-device] [skb-priority] [vlan-qos]
This flags that inbound packets with the particular vlan priority vlan-qos should be queued with a particular skb-priority. The
default skb-priority is 0.
set_name_type VLAN_PLUS_VID | VLAN_PLUS_VID_NO_PAD | DEV_PLUS_VID | DEV_PLUS_VID_NO_PAD
Sets the way vlan-device names are created. Use vconfig without arguments to see the different formats.
NOTES VLAN will use Broadcom's NICE interface when the network device supports it. This is necessary, since usually the hardware of these
devices already removes the vlan tag from the ethernet packet. The set_flag option on vlan-devices created on such a physical net-
work device will be ignored. Dumping the network-device will show only untagged(non-vlan) traffic, and dumping the vlan-devices
will only show traffic intended for that vlan, without the tags.
FILES
/proc/net/vlan/config
/proc/net/vlan/[vlan-device]
SEE ALSO
ip(8), ifconfig(8)
AUTHORS
This manual page was written by Ard van Breemen <ard@kwaak.net>
The vlan patch is written by Ben Greear <greearb@candelatech.com>
VCONFIG(8)