03-07-2013
i have done it with iscsi. and, yes, i assume the no_resdrve setting is also needed. been nearly 18 months since i have played with ha.
have fun.
ps, if working with systemmirror 7.x remember that the ha interfaces will multicast for caa. if you have a lot of systems in a vlan they may be affected..
10 More Discussions You Might Find Interesting
1. AIX
Hello,
I would like to know if anyone has faced this problem. Whenever there is a duplicate IP address, HACMP goes down infact HACMP ( PowerHA ) takes the whole system down.
Does anyone know how to solve this problem ? (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
3. AIX
I am planning for building a new database server using AIX 6.1 and Oracle 11.2 using ASM.
As i have learned starting with Oracle 11.2 ASM can only be used in conjunction with Clusterware, which is Oracles HA-software. As is the companies policy we do intend to use PowerHA as HA-solution instead... (1 Reply)
Discussion started by: bakunin
1 Replies
4. AIX
Hello!
I have this infraestructure:
- 1 POWER7 with single VIOS on Site A.
- 1 POWER6 with single VIOS on Site B.
- 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A.
- 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB.
- 1 Storage DS4700 on Site A.
- 1... (8 Replies)
Discussion started by: enzote
8 Replies
5. AIX
Hello AIX GURU's
Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server?
my questions are:
1.
Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar?
or
2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Hello,
AIX 6.1 TL7 SP6
POwerHA 6.1 SP10
I was experimenting with new hacmp build. It's 3-node cluster build on AIX 6.1 lpars. It contains Ethernet and diskhb networks. Shared vg disk is SAN disk. Two nodes see disk using vscsi, third node sees disk using npiv. Application is db2 server.
... (4 Replies)
Discussion started by: vilius
4 Replies
8. AIX
hello
ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415
work with dmx4 EMC storgae.
after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine :
hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies
9. AIX
I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp.
Please share me steps for adding vxvm diskgroup to hacmp. (6 Replies)
Discussion started by: sunnybee
6 Replies
10. AIX
Hi All,
As per the IBM upgrade/support matrix
IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix
we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ...
1 ) Bring down the cluster
2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)
NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO
vconfig(8) interfaces(5)
vlan September 30 2007 VLAN-INTERFACES(5)