03-07-2013
Quote:
Originally Posted by
MichaelFelt
yes, you can if the stoarge is an hdisk to the vios, not when the storage is a file or logical volume.
if i recall, just repeat the mkvdev command.
So, I can assign same HDISK to two or more , LPARs
example: from SAN Storage I have allocated HDISK8 to PowerVM IVM
I will have to create virtual scsi for all three LPARs
then assign HDISK8 to them, and as you mentioned above would have to set the reserve_policy=no_reserve .
is this right ?
10 More Discussions You Might Find Interesting
1. AIX
Hello,
I would like to know if anyone has faced this problem. Whenever there is a duplicate IP address, HACMP goes down infact HACMP ( PowerHA ) takes the whole system down.
Does anyone know how to solve this problem ? (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
3. AIX
I am planning for building a new database server using AIX 6.1 and Oracle 11.2 using ASM.
As i have learned starting with Oracle 11.2 ASM can only be used in conjunction with Clusterware, which is Oracles HA-software. As is the companies policy we do intend to use PowerHA as HA-solution instead... (1 Reply)
Discussion started by: bakunin
1 Replies
4. AIX
Hello!
I have this infraestructure:
- 1 POWER7 with single VIOS on Site A.
- 1 POWER6 with single VIOS on Site B.
- 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A.
- 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB.
- 1 Storage DS4700 on Site A.
- 1... (8 Replies)
Discussion started by: enzote
8 Replies
5. AIX
Hello AIX GURU's
Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server?
my questions are:
1.
Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar?
or
2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Hello,
AIX 6.1 TL7 SP6
POwerHA 6.1 SP10
I was experimenting with new hacmp build. It's 3-node cluster build on AIX 6.1 lpars. It contains Ethernet and diskhb networks. Shared vg disk is SAN disk. Two nodes see disk using vscsi, third node sees disk using npiv. Application is db2 server.
... (4 Replies)
Discussion started by: vilius
4 Replies
8. AIX
hello
ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415
work with dmx4 EMC storgae.
after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine :
hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies
9. AIX
I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp.
Please share me steps for adding vxvm diskgroup to hacmp. (6 Replies)
Discussion started by: sunnybee
6 Replies
10. AIX
Hi All,
As per the IBM upgrade/support matrix
IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix
we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ...
1 ) Bring down the cluster
2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LEARN ABOUT NETBSD
vgreduce
VGREDUCE(8) System Manager's Manual VGREDUCE(8)
NAME
vgreduce - reduce a volume group
SYNOPSIS
vgreduce [-a|--all] [-A|--autobackup y|n] [-d|--debug] [-h|-?|--help] [--removemissing] [-t|--test] [-v|--verbose] VolumeGroupName [Physi-
calVolumePath...]
DESCRIPTION
vgreduce allows you to remove one or more unused physical volumes from a volume group.
OPTIONS
See lvm for common options.
-a, --all
Removes all empty physical volumes if none are given on command line.
--removemissing
Removes all missing physical volumes from the volume group, if there are no logical volumes allocated on those. This resumes normal
operation of the volume group (new logical volumes may again be created, changed and so on).
If this is not possible (there are logical volumes referencing the missing physical volumes) and you cannot or do not want to remove
them manually, you can run this option with --force to have vgreduce remove any partial LVs.
Any logical volumes and dependent snapshots that were partly on the missing disks get removed completely. This includes those parts
that lie on disks that are still present.
If your logical volumes spanned several disks including the ones that are lost, you might want to try to salvage data first by acti-
vating your logical volumes with --partial as described in lvm (8).
SEE ALSO
lvm(8), vgextend(8)
Sistina Software UK LVM TOOLS 2.02.44-cvs (02-17-09) VGREDUCE(8)