02-26-2013
sohail Jafferi,
Can you provide more details about your install.? If this is the first install do you configure your disk properly?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I'm getting this error when booting:
" Timeout waiting for ARP/RARP packet"
I got no idea what has been done to get it when the machine use to work fine. Put a new HDD in it, and installed Solaris 7 on it fine then when it goes to boot I get that error.
It's a Sparc Station 5... (2 Replies)
Discussion started by: merlin
2 Replies
2. UNIX for Dummies Questions & Answers
Hey all,
When loading a Sun Ultra 60 I got running Solaris 9 I get a error. This error will only happen when I have a external CD-RW drive attached.
The error is;
Failed to power up sd21, see your administrator or reboot
I have rebooted and well I am the administrator for this machine.... (5 Replies)
Discussion started by: merlin
5 Replies
3. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
4. UNIX for Dummies Questions & Answers
VERY new to Unix here! I have a client with a unix machine(Sun Systems Unix system V Release 4.0) that gets an error on boot up.
"7.e.1": Syntax error in tty mode
Like I said, I new to Unix as this is my first time ever touching a Unix machine. So, I don't know if this is a major or minor... (0 Replies)
Discussion started by: rlpierce04
0 Replies
5. AIX
Hi all,
I have one booting problem with an AIX machine. It is not booting.
It is showing error B1014602 on OK prompt.
Could you please tell me, what is the problem with it and its respective solution?
Thank you very much. (2 Replies)
Discussion started by: prashantchavan
2 Replies
6. Linux
Hi,
I need to install Oracle Enterprise Linux 5.0 on IBM3400.Before start it,I expect your valuable suggestions regarding partition size...etc.
This server is having 146 GB of hard disk and 4GB of RAM.I need to create 15 restricted users on this server.These 15 users will access their folders... (1 Reply)
Discussion started by: masatheesh
1 Replies
7. SCO
hi
SCO Unix 5.0.6 doesn't boot due to this problem:
not a directory
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot
Knows someone howto solve it? (16 Replies)
Discussion started by: ccc
16 Replies
8. Red Hat
Hi All,
I have an issue when trying to hot-add a SAN disk to an oracle enterprise linux 5.5 server.
The storage array we are using is an HP 24000, we have no issues with the disk usage for both ASM and LVM setup, it is just a simple matter of not being able to scan for new disk when it is... (4 Replies)
Discussion started by: Tommyk
4 Replies
9. UNIX for Advanced & Expert Users
Server Model
HP Proliant DL380P, Gen 8
Raid Controller= HP smart Array P420i
Operating system Installation OEl5.8
On first boot after OS installation
ERROR:
Red Hat nash Version 5.119.6 starting -300.10.1.el5uek)’
Mounting proc Filesystem
Reading all physical volume this may take a... (0 Replies)
Discussion started by: sohail Jafferi
0 Replies
IDA(4) BSD Kernel Interfaces Manual IDA(4)
NAME
ida -- Compaq Intelligent Drive Array Controllers
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ida
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ida_load="YES"
DESCRIPTION
The Compaq Intelligent Drive Array (IDA) technology is used to distribute data across an array of hard drives. It unites these hard drives
into one or more high-performance logical drives. The drive array is managed by an array controller.
These controllers have the ability to provide fault tolerance for the connected drives and optionally provide write cache for the logical
drives. It is also possible for an application to access the SCSI bus subsystem directly by using the pass-through interface.
HARDWARE
The following controllers are supported by the ida driver:
o Compaq SMART Array 221
o Compaq Integrated SMART Array Controller
o Compaq SMART Array 4200
o Compaq SMART Array 4250ES
o Compaq SMART 3200 Controller
o Compaq SMART 3100ES Controller
o Compaq SMART-2/DH Controller
o Compaq SMART-2/SL Controller
o Compaq SMART-2/P Controller
o Compaq SMART-2/E Controller
o Compaq SMART Controller
IMPLEMENTATION NOTES
Extreme caution should be exercised when using the pass-through interface. It is possible to interfere with normal system I/O and cause
hangs if pass-through is used to an active device. Pass-through should only be used to a device that is otherwise quiescent.
SEE ALSO
cam(4), pass(4), xpt(4), camcontrol(8)
AUTHORS
The ida driver was written by Jonathan Lemon <jlemon@FreeBSD.org> and Matthew N. Dodd <mdodd@FreeBSD.org>. This manual page was written by
Tom Rhodes <trhodes@FreeBSD.org>.
BSD
August 8, 2004 BSD