|
|
Sponsored Content
Top Forums
UNIX for Advanced & Expert Users
Grub - how to boot a copy of Linux (full system backup)
Post 302765975 by coolatt on Monday 4th of February 2013 02:55:05 AM
02-04-2013
Quote:
Its easy, a two step process.
You only need to edit grub.conf to add another boot option only for the vmlinux image you get into SystemBackup02/boot directory. Run 'install-grub /dev/<device holding SystemBackup02>'.
Hope both primary and backup machines have same architecture & device configurations!!!
A word of caution: It's a bit risky with little scope for mistakes; however don't assume that you are doomed on your mistake (until you delete your own data), if the backup system doesn't boot. You'll need to re-boot them again with a backup CD images and mount the drives temporarily and re-do the process correctly, BUT this time differently (mind that mounting may change paths). I've landed into mess and bounced back too but tensions run always high.
You only need to edit grub.conf to add another boot option only for the vmlinux image you get into SystemBackup02/boot directory. Run 'install-grub /dev/<device holding SystemBackup02>'.
Hope both primary and backup machines have same architecture & device configurations!!!
A word of caution: It's a bit risky with little scope for mistakes; however don't assume that you are doomed on your mistake (until you delete your own data), if the backup system doesn't boot. You'll need to re-boot them again with a backup CD images and mount the drives temporarily and re-do the process correctly, BUT this time differently (mind that mounting may change paths). I've landed into mess and bounced back too but tensions run always high.
)Also note that the "SystemBackup02" is just another directory on the same disk /dev/sda.
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed Linux 7.2 on a IBM xseries 235 server with 5 scsi hard drives and ServerRaid-5i Ultra320 scsi controller.
I started my installation by configuring the raid controller. I created 2 arrays, raid 1 and raid5. I then proceeded to install Linux and load the drivers.
After the... (2 Replies)
Discussion started by: cstovall
2 Replies
2. Red Hat
my redhat 9 will not boot. We had a power failure and when the power came back, my redhat linux will not boot.
The machine come up to grub prompt.
I tried the following from grub prompt
root (hd0, then press tab key
partition num:0 filesystem type unknown, partition type 0x83... (7 Replies)
Discussion started by: hassan2
7 Replies
3. UNIX for Dummies Questions & Answers
I am new to UNIX and need help in cloning a HPUX 10.2 Ace 5, can anybody please guide me in making a full system backup.
Real Chess (0 Replies)
Discussion started by: real-chess
0 Replies
4. Linux
Please help. I am new to linux. I wrote a script to run the backup on lunix machine but the job gave me an error. I am using Linux 2.6.14.3. Below is the sample of my script can anyone tell me where went wrong? Thanks in advance.
#!/bin/sh
dat=$(date +%d%b%y)... (5 Replies)
Discussion started by: clement
5 Replies
5. UNIX for Dummies Questions & Answers
hi,
Recently, I had receive one system. it's run on the unix tru64 server.
I looking some log files when i know don't work few months age system backup to tape.
Below error:
INFO:Tape backups to tape tape0 starting
for backup list:
slot2:/disk4
Backup Command Variable... (0 Replies)
Discussion started by: Tlg13team
0 Replies
6. Solaris
I have unix server with OS 5.8 ,,,
I tried ufsdump 0ua -f /dev/rmt/0 / to perform full system backup on tape but I failed could any one give a procedure for full system backup on solaris machine using tapes??? (1 Reply)
Discussion started by: mm00123
1 Replies
7. UNIX for Dummies Questions & Answers
I would like to know if I can do a full system back
up on my Unix Sco openserver 5.0.5 Machine. If so, What
is the syntax to do this or where can I find this
information at?
Also, is it possible to make this tape bootable so
that I can easily do a full system restore? Any
information on... (2 Replies)
Discussion started by: nellenodrog
2 Replies
8. HP-UX
Hello,
I'm still new in HP-UX backup and I want to do a FULL BACKUP of HP-UX server to TAPE device. After reading on several forums and posts, i have list down several steps on how to do a full backup on HP-UX with fbackup. I would like the gurus here to comment/advise on the steps below
1)... (4 Replies)
Discussion started by: miskin
4 Replies
9. UNIX for Advanced & Expert Users
Hi,
In order to have a sand box machine that I could use to test some system changes before going to production state, I'd like to duplicate a working system to a virtual one. Ideally, I'd like to manage to do it this way :
- Make a full system backup excluding the user file system (this... (7 Replies)
Discussion started by: pagaille
7 Replies
10. Solaris
Hello i am new on Solaris, and i need to migrate my old AIX 5.3 to Solaris 11.2
Now i have all apps working fine but i have the backup cause i was reading and i have not idea about what method must i choose.
Btw on AIX i had a mksysb backup to restore all system and obviously another backups to... (4 Replies)
Discussion started by: thorin666
4 Replies
LEARN ABOUT OPENSOLARIS
vgcfgrestore
VGCFGRESTORE(8) System Manager's Manual VGCFGRESTORE(8) NAME
vgcfgrestore - restore volume group descriptor area SYNOPSIS
vgcfgrestore [-d|--debug] [-f|--file filename] [-l[l]|--list] [-h|--help] [-M|--Metadatatype1|2] [-t|--test] [-v|--verbose] VolumeGroupName DESCRIPTION
vgcfgrestore allows you to restore the metadata of VolumeGroupName from a text backup file produced by vgcfgbackup. You can specify a backup file with --file. If no backup file is specified, the most recent one is used. Use --list for a list of the available backup and archive files of VolumeGroupName. OPTIONS
-l | --list -- List files pertaining to VolumeGroupName List metadata backup and archive files pertaining to VolumeGroupName. May be used with the -f option. Does not restore Vol- umeGroupName. -f | --file filename -- Name of LVM metadata backup file Specifies a metadata backup or archive file to be used for restoring VolumeGroupName. Often this file has been created with vgcfg- backup. See lvm for common options. REPLACING PHYSICAL VOLUMES
vgdisplay --partial --verbose will show you the UUIDs and sizes of any PVs that are no longer present. If a PV in the VG is lost and you wish to substitute another of the same size, use pvcreate --restorefile filename --uuid uuid (plus additional arguments as appropriate) to initialise it with the same UUID as the missing PV. Repeat for all other missing PVs in the VG. Then use vgcfgrestore --file filename to restore the volume group's metadata. SEE ALSO
lvm(8), vgcreate(8) Sistina Software UK LVM TOOLS 2.02.95(2) (2012-03-06) VGCFGRESTORE(8)