02-04-2013
Hi..i have 4 lan port configured with different gateway. when i tried running command getting below output.
/etc/sysconfig/network-scripts/ifcfg-eth0:GATEWAY=x1.x2.x3.x4
/etc/sysconfig/network-scripts/ifcfg-eth1:GATEWAY=x11.x12.x13.x14
/etc/sysconfig/network-scripts/ifcfg-eth2:GATEWAY=x21.x22.x23.x24
/etc/sysconfig/network-scripts/ifcfg-eth3:GATEWAY=x31.x32.x33.x34
9 More Discussions You Might Find Interesting
1. Solaris
my actual default gatewas IP is:
default 192.168.11.254
and I need to change it to 192.168.11.2, I'm using Solaris 9, how can i do it? and how i can save it in case that the machine restart and have the new default gateway IP saved? (5 Replies)
Discussion started by: Lestat
5 Replies
2. Shell Programming and Scripting
Hello all!
We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our... (0 Replies)
Discussion started by: slacker
0 Replies
3. AIX
Hi,
I have two interfaces on m AIX 5.3 box. One going to 192.168.1.x and it has a gateway of 192.168.1.1.
I configured the other gateway with 192.168.2.x and the default gateway as 192.168.2.1. But I can't get connectivity to the 192.168.2.1 network. Can someone help me out and let me know... (7 Replies)
Discussion started by: bbbngowc
7 Replies
4. Solaris
Hi Gurus
Recently i had change the gateway for a server
i had change the IP in the /etc/defaultrouter
and run the below command
# route add default 10.86.33.222
# route delete default 10.86.33.1
# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref ... (2 Replies)
Discussion started by: SmartAntz
2 Replies
5. HP-UX
where in configuration files can i modify default gateway in hp-ux11iv3 (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
6. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
7. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
8. IP Networking
I am am using IPv6 IP's with an OS of Debian.
Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected?
TIA (0 Replies)
Discussion started by: Meow613
0 Replies
9. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
ocf_heartbeat_route
OCF_HEARTBEAT_ROUTE(7) OCF resource agents OCF_HEARTBEAT_ROUTE(7)
NAME
ocf_heartbeat_Route - Manages network routes
SYNOPSIS
Route [start | stop | monitor | meta-data | validate-all]
DESCRIPTION
Enables and disables network routes.
Supports host and net routes, routes via a gateway address, and routes using specific source addresses.
This resource agent is useful if a node's routing table needs to be manipulated based on node role assignment. Consider the following
example use case: - One cluster node serves as an IPsec tunnel endpoint. - All other nodes use the IPsec tunnel to reach hosts in a
specific remote network. Then, here is how you would implement this scheme making use of the Route resource agent: - Configure an ipsec LSB
resource. - Configure a cloned Route OCF resource. - Create an order constraint to ensure that ipsec is started before Route. - Create a
colocation constraint between the ipsec and Route resources, to make sure no instance of your cloned Route resource is started on the
tunnel endpoint itself.
SUPPORTED PARAMETERS
destination
The destination network (or host) to be configured for the route. Specify the netmask suffix in CIDR notation (e.g. "/24"). If no
suffix is given, a host route will be created. Specify "0.0.0.0/0" or "default" if you want this resource to set the system default
route. (unique, required, string, no default)
device
The outgoing network device to use for this route. (unique, optional, string, no default)
gateway
The gateway IP address to use for this route. (unique, optional, string, no default)
source
The source IP address to be configured for the route. (unique, optional, string, no default)
table
The routing table to be configured for the route. (optional, string, no default)
SUPPORTED ACTIONS
This resource agent supports the following actions (operations):
start
Starts the resource. Suggested minimum timeout: 20.
stop
Stops the resource. Suggested minimum timeout: 20.
monitor
Performs a detailed status check. Suggested minimum timeout: 20. Suggested interval: 10.
reload
Suggested minimum timeout: 20.
meta-data
Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5.
validate-all
Performs a validation of the resource configuration. Suggested minimum timeout: 20.
EXAMPLE
The following is an example configuration for a Route resource using the crm(8) shell:
primitive p_Route ocf:heartbeat:Route
params
destination=string
op monitor timeout="20" interval="10" depth="0"
SEE ALSO
http://www.linux-ha.org/wiki/Route_(resource_agent)
AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors)
resource-agents UNKNOWN 03/09/2014 OCF_HEARTBEAT_ROUTE(7)