02-04-2013
Hi..i have 4 lan port configured with different gateway. when i tried running command getting below output.
/etc/sysconfig/network-scripts/ifcfg-eth0:GATEWAY=x1.x2.x3.x4
/etc/sysconfig/network-scripts/ifcfg-eth1:GATEWAY=x11.x12.x13.x14
/etc/sysconfig/network-scripts/ifcfg-eth2:GATEWAY=x21.x22.x23.x24
/etc/sysconfig/network-scripts/ifcfg-eth3:GATEWAY=x31.x32.x33.x34
9 More Discussions You Might Find Interesting
1. Solaris
my actual default gatewas IP is:
default 192.168.11.254
and I need to change it to 192.168.11.2, I'm using Solaris 9, how can i do it? and how i can save it in case that the machine restart and have the new default gateway IP saved? (5 Replies)
Discussion started by: Lestat
5 Replies
2. Shell Programming and Scripting
Hello all!
We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our... (0 Replies)
Discussion started by: slacker
0 Replies
3. AIX
Hi,
I have two interfaces on m AIX 5.3 box. One going to 192.168.1.x and it has a gateway of 192.168.1.1.
I configured the other gateway with 192.168.2.x and the default gateway as 192.168.2.1. But I can't get connectivity to the 192.168.2.1 network. Can someone help me out and let me know... (7 Replies)
Discussion started by: bbbngowc
7 Replies
4. Solaris
Hi Gurus
Recently i had change the gateway for a server
i had change the IP in the /etc/defaultrouter
and run the below command
# route add default 10.86.33.222
# route delete default 10.86.33.1
# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref ... (2 Replies)
Discussion started by: SmartAntz
2 Replies
5. HP-UX
where in configuration files can i modify default gateway in hp-ux11iv3 (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
6. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
7. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
8. IP Networking
I am am using IPv6 IP's with an OS of Debian.
Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected?
TIA (0 Replies)
Discussion started by: Meow613
0 Replies
9. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT NETBSD
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-adIlnrv] [-A as_server] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
-A Turn on AS# lookups and use the given server instead of the default.
-a Turn on AS# lookups for each hop encountered.
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-I Use ICMP6 ECHO instead of UDP datagrams.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-m hoplimit
Specify maximum hoplimit.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached net-
work, an error is returned. This option can be used to send probes to a local host through an interface that has no route through it
(e.g., after the interface was dropped by route6d(8)).
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
EXIT STATUS
The traceroute6 command exits 0 on success, and >0 on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
September 17, 2005 BSD