Hi all,
I am running an oracle application server but the problem is that the default port it is using is 7777 and if i want to make it port 80 i have to run the server as root which something i do not want to do. If i understand well to run on a port under 1024 the application needs root... (1 Reply)
Dear All..
I have an HP-UX server, i need to access it through certain port to run application.., but i cant access it,
I can login as root by using other port
Can anyone give me any advice how to see the list of active port? and how to block / unblock it??
Thankyou in advance
... (1 Reply)
Dear Expects,
I am facing following discrepancies on our server.
a) When we give wrong root password three times in a row, the root account has been disabled.
b) System is forced to change the old password, whenever we tried to change the password of any of the OS user and for ROOT user... (2 Replies)
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Hi Guys,
Some of the websites are blocked in my office. And I know the root password.
I tried to unblock those sites.. Checkedcd /etc/modprobe.d
$ cat blacklist.conf
#
# Listing a module here prevents the hotplug scripts from loading it.
# Usually that'd be so that some other driver will... (8 Replies)
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LEARN ABOUT DEBIAN
net::smtp::server::client
Server::Client(3pm) User Contributed Perl Documentation Server::Client(3pm)NAME
Net::SMTP::Server::Client - Client session handling for Net::SMTP::Server.
SYNOPSIS
use Carp;
use Net::SMTP::Server;
use Net::SMTP::Server::Client;
use Net::SMTP::Server::Relay;
$server = new Net::SMTP::Server('localhost', 25) ||
croak("Unable to handle client connection: $!
");
while($conn = $server->accept()) {
# We can perform all sorts of checks here for spammers, ACLs,
# and other useful stuff to check on a connection.
# Handle the client's connection and spawn off a new parser.
# This can/should be a fork() or a new thread,
# but for simplicity...
my $client = new Net::SMTP::Server::Client($conn) ||
croak("Unable to handle client connection: $!
");
# Process the client. This command will block until
# the connecting client completes the SMTP transaction.
$client->process || next;
# In this simple server, we're just relaying everything
# to a server. If a real server were implemented, you
# could save email to a file, or perform various other
# actions on it here.
my $relay = new Net::SMTP::Server::Relay($client->{FROM},
$client->{TO},
$client->{MSG});
}
DESCRIPTION
The Net::SMTP::Server::Client module implements all the session handling required for a Net::SMTP::Server::Client connection. The above
example demonstrates how to use Net::SMTP::Server::Client with Net::SMTP::Server to handle SMTP connections.
$client = new Net::SMTP::Server::Client($conn)
Net::SMTP::Server::Client accepts one argument that must be a handle to a connection that will be used for communication.
Once you have a new client session, simply call:
$client->process
This processes an SMTP transaction. THIS MAY APPEAR TO HANG -- ESPECIALLY IF THERE IS A LARGE AMOUNT OF DATA BEING SENT. Once this method
returns, the server will have processed an entire SMTP transaction, and is ready to continue.
Once $client->process returns, various fields have been filled in. Those are:
$client->{TO} -- This is an array containing the intended
recipients for this message. There may be
multiple recipients for any given message.
$client->{FROM} -- This is the sender of the given message.
$client->{MSG} -- The actual message data. :)
AUTHOR AND COPYRIGHT Net::SMTP::Server / SMTP::Server is Copyright(C) 1999, MacGyver (aka Habeeb J. Dihu) <macgyver@tos.net>. ALL RIGHTS
RESERVED.
You may distribute this package under the terms of either the GNU General Public License or the Artistic License, as specified in the Perl
README file.
SEE ALSO
Net::SMTP::Server::Server, Net::SMTP::Server::Relay
perl v5.10.1 1999-12-28 Server::Client(3pm)