01-23-2013
You should be able to use multiple --disk options.
8 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I want to install pecl from a single command without it asking me for a response of "yes" or "no" to finish the install...
--------------------------------------------------------------------------
# pecl install pecl_http
downloading pecl_http-1.7.0.tgz ...
Starting to download... (1 Reply)
Discussion started by: sjsotelo
1 Replies
2. Debian
Does any one have some words on this ' microprocessor '* and if there should be any attempt to install Debian Linux into it.
Thank you
I have looked at this page:
2.1.*Supported Hardware
2.1 Supported Hardware
Chapter 2. System Requirements
and crossed check many times and do not see any... (4 Replies)
Discussion started by: cowLips
4 Replies
3. UNIX for Advanced & Expert Users
Hi,
I've a CentOS Server and I need to create KVM guest machine without X.
/usr/sbin/virt-install --name server1 --ram 4000 --vcpus=8 --file=/srv/virtual/server1.img --file-size=20 --cdrom /tmp/server1.iso --mac=52:54:00:fd:48:7c
The iso was created with cobbler...
So, now the machine is... (5 Replies)
Discussion started by: hiddenshadow
5 Replies
4. Red Hat
Hi,
I am trying to install git on RHEL 6. From the research I have done I should be able to just say:
sudo yum install git
but it is not working (it says no package git is available). I am fairly new to linux and cannot figure this out.
Thanks for any help you can provide. (7 Replies)
Discussion started by: dsabol
7 Replies
5. Solaris
Hi Guys,
One of two disks in my solaris machine has failed, the name is disk0, this is SUN physical sparc machine
But I work remotely, so people working near that physical server are not that technical, so from OS command prompt can run some command to bink faulty disk at front panel of Server.... (9 Replies)
Discussion started by: manalisharmabe
9 Replies
6. Shell Programming and Scripting
Hi gurus,
I hit a block when write the script.
I need do while loop, in the loop I have code below.
sqlplus -s abc/abc@abc <<EOF
spool testwhile
select *
from dual;
spool off
exit;
EOF
when I run script with only this code, it works fine.
if I add code as below:
#!/bin/ksh
... (5 Replies)
Discussion started by: ken6503
5 Replies
7. Red Hat
Hello guys!
First of all sorry about my english.
I am using KVM to virtualizate. But when i run the virt-install command, it shows the next error:
ERROR Host does not support any virtualization options.My server had virtualisation extensions enabled in the bios.
It is my first time using... (7 Replies)
Discussion started by: morrison71
7 Replies
8. UNIX for Beginners Questions & Answers
I have downloaded RHEV-H 4.2 Red Hat Virtualization - Red Hat Customer Portal (RHVirtualization 4.2 Host and Manager iso). I uploaded the image and installed on an HP G9 server baremetal.
I found I dont have a WAN/net connectivity later on HPG9 server. How can I still install virt-manager on... (1 Reply)
Discussion started by: Paras Pandey
1 Replies
LEARN ABOUT NETBSD
apmlabel
APMLABEL(8) BSD System Manager's Manual APMLABEL(8)
NAME
apmlabel -- update disk label from Apple Partition Map
SYNOPSIS
apmlabel [-fqrw] device
DESCRIPTION
apmlabel is used to update a NetBSD disk label from the Apple Partition Map found on disks that were previously used on Mac OS systems (or
other APM using systems).
apmlabel scans the APM contained in the first blocks of the disk and generates additional partition entries for the disk from the entries
found. Driver and patches partitions are ignored.
Each APM entry which does not have an equivalent partition in the disk label (equivalent in having the same size and offset) is added to the
first free partition slot in the disk label. A free partition slot is defined as one with an fstype of 'unused' and a size of zero ('0').
If there are not enough free slots in the disk label, a warning will be issued.
The raw partition (typically partition c, but d on i386 and some other platforms) is left alone during this process.
By default, the proposed changed disk label will be displayed and no disk label update will occur.
Available options:
-f Force an update, even if there has been no change.
-q Performs operations in a quiet fashion.
-r In conjunction with -w, also update the on-disk label.
-w Update the in-core label if it has been changed.
SEE ALSO
disklabel(8), dkctl(8), pdisk(8)
HISTORY
The apmlabel command appeared in NetBSD 5.0.
BSD
May 19, 2007 BSD