01-02-2013
Thank you for writing a follow-up.
Moderator's Comments:
|
|
changed the thread title to SOLVED
|
|
bakunin
10 More Discussions You Might Find Interesting
1. AIX
When using PowerVM Express and IVM (no HMC) on a Power6 P520 , can I configure 2 LPARs in addition to a VIO server, or does the VIO Server count as one of the two LPAR's that PowerVM Express allows? (1 Reply)
Discussion started by: JodyTek
1 Replies
2. HP-UX
Please help me >
How to diag the external DVD-ROM drive issue whether it is working or not? on HP 9000 server rp7400
I needed to install HP 11i v1 using external DVD-ROM drive on HP 9000 server rp7400. While boot in CO> “search” command is not showing DVD-ROM device only showing all disks >... (0 Replies)
Discussion started by: tpuser
0 Replies
3. UNIX for Advanced & Expert Users
old clunker - rp74000
How to diag the external DVD-ROM drives issue whether it is working or not? on HP 9000 server rp7400
Please help me > I needed to install HP 11i v1 using external DVD-ROM drive on HP 9000 server rp7400. While boot in CO> “search” command is not showing DVD-ROM device... (1 Reply)
Discussion started by: tpuser
1 Replies
4. AIX
Hi everyone,
Sorry if this post is in the wrong place. I searched the forums for "IVM" and it turned up no results. Hopefully someone knows about this. My dilemma is that I have multiple IBM JS12 Express blades in our blade center, each running VIOS 2.1.0.10-FP-20.1 and hosting a couple LPARs. Out... (2 Replies)
Discussion started by: need2bageek
2 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. AIX
Hi,
When I try to login on my vios ivm website http://vios through the browser -- all three of them -- firefox , chrome , Internet Explorer , i get this error
http://vioserver/j_security_check
I have java installed on the machine from where i am trying to open up the IVM/VIOS webpage.
I... (2 Replies)
Discussion started by: filosophizer
2 Replies
7. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
8. AIX
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies
9. AIX
coming from this thread: https://www.unix.com/aix/211107-ibm-power-pseries-open-firmware-boot-vios-powervm-vet-code.html
PowerVM, formerly known as Advanced Power Virtualization (APV), is a chargeable feature of IBM POWER5, POWER6, POWER7, POWER8, and POWER9 servers and is required for support... (0 Replies)
Discussion started by: filosophizer
0 Replies
10. AIX
Hello,
After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )
i get this message
"I/O hosting requires a hosting partition - boot not permitted".
HMC was connected to the machine
then HMC was removed through ASMI
Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies
LEARN ABOUT DEBIAN
lighty-enable-mod
LIGHTYENABLEMOD(1) General Commands Manual LIGHTYENABLEMOD(1)
NAME
lighty-enable-mod, lighty-disable-mod - enable or disable configuration in lighttpd server
SYNOPSIS
lighty-enable-mod [module]
lighty-disable-mod [module]
DESCRIPTION
This manual page documents briefly the lighty-enable-mod and lighty-disable-mod commands.
lighty-enable-mod and lighty-disable-mod are programs that enable (and respectively disable) the specified configuration file within
lighttpd configuration.
Both programs can be run interactively or from command line. If either program is called without any arguments, an input prompt is dis-
played to the user, where he might choose among available lighttpd modules. Immediate action is taken, if a module name was given on the
command line.
EXIT STATUS
Both programs indicate failure in their exit status. lighty-enable-mod or lighty-disable-mod respectively may leave execution with one of
the following exit codes:
0 denotes success
1 denotes a fatal error (e.g., a module could not be enabled, or a dependency was not found)
2 denotes a minor flaw (e.g., a module was not enabled because it was already loaded before)
Note
You can (un-) load several modules at time. The exit status will only reflect the most serious issue (where a minor flaw beats no error,
but a fatal error beats a minor flaw). This means, if a minor flaw was encountered as well as a fatal error, the program will leave with
exit status 1 and stop immediately.
DEPENDENCIES
Debian allows lighttpd modules to formulate dependencies to other modules they depend on. Configuration files are scanned for dependencies
upon load or unload of modules, not at runtime of the web server. Such a magic line has the following format:
# -*- depends: module[, module] -*-
and may appear anywhere in the file. If such a line is found, the extracted name is interpreted as dependency to another lighttpd module.
lighty-enable-mod will seek available configurations to satisfy this dependency and will recursively enable all dependencies found on its
way. lighty-disable-mod will disable reverse dependencies recursively.
SEE ALSO
lighttpd(1)
AUTHOR
Program and man pages were originally written by Krzysztof Krzyaniak <eloy@debian.org> and later modified by Arno Toll <debian@toell.net>
2006-01-11 LIGHTYENABLEMOD(1)