Sponsored Content
Full Discussion: Unable to ping localhost
Operating Systems AIX Unable to ping localhost Post 302747305 by Scott on Friday 21st of December 2012 04:09:00 AM
Old 12-21-2012
Try with:
Code:
# ifconfig lo | grep RUNNING
UP LOOPBACK RUNNING MTU:16436 Metric:1

A couple of other questions. Is this a new problem? Are you running a firewall (i.e. iptables)?
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Unable to ping host

Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: - 1 QNX host->Eth->1 SCO host the SCO host is configured with it's IP the QNX host is configured with another IP both in the same domain, ie, 172.20.3.XX... (3 Replies)
Discussion started by: gavon
3 Replies

2. UNIX for Dummies Questions & Answers

NIC The Status Down but I can ping the localhost??!!

Hello, hi guys I don't know what is the problem with my NIC I can ping the Localhost (LOOPBACK) but when I run a scripts to check the NIC statuse it's shown the NIC DOWN sooo what could be the problem and what is the best way to start trouplshooting the NIC in SUN-SOLARIS. Regards, Karim ... (3 Replies)
Discussion started by: geoquest
3 Replies

3. UNIX for Dummies Questions & Answers

unable ping ipaddress

I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the etc/tcp etc/hosts files which i did. still unable to ping. i am getting a message unable to route to host. I also have an error in my etc/tcp file on line... (1 Reply)
Discussion started by: pdoug76
1 Replies

4. UNIX for Dummies Questions & Answers

unable to ping

DEar all i am receiving this error on start and then unable to ping (dlpid): unable to open network adapter driver (/dev/mdi/e3h0) what to do ? (2 Replies)
Discussion started by: sak900354
2 Replies

5. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies

6. Solaris

unable to ping server

hi, I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise? Test that i have done: -My client pc cannot ping the server. -My solaris server cannot ping client -My solaris server can ping it's gateway -Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
Discussion started by: skiturn
2 Replies

7. IP Networking

unable to ping to my server

hi, I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise? Test that i have done: -My client pc cannot ping the server. -My solaris server cannot ping client -My solaris server can ping it's gateway -Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Discussion started by: skiturn
8 Replies

8. Solaris

Unable to ping New server

Hi ALL, I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network bk (1 Reply)
Discussion started by: suresh_krish
1 Replies

9. Solaris

Unable to ping Windows

Hello, Am unable to ping the Windows Box, from my Solaris Box. They both are in same LAN, have the same IP Segments. Windows IP :: 10.141.14.120 Solaris IP :: 10.141.14.11 Unable to get why isnt working out.... When using the command 'ping 10.141.14.120', it gives the error as 'ping:... (4 Replies)
Discussion started by: jayanto
4 Replies

10. IP Networking

Unable to connect to localhost in Debian 6?

Hello Everyone, I have unable to run the default server with localhost in my Debian machine. While trying to run Django I get: Error: That IP address can't be assigned-to. error While trying to run galaxy-dist I get this error: socket.error: Cannot assign requested address I can't telnet... (3 Replies)
Discussion started by: sachit adhikari
3 Replies
asadmin-jms-ping(1AS)						   User Commands					     asadmin-jms-ping(1AS)

NAME
jms-ping - checks to see if the JMS provider is up and running SYNOPSIS
jms-ping --user admin_user [--password admin_password] [--host localhost] [--port 4848] [--passwordfile filename] [--secure|-s] [--terse=false] [--echo=false] [--interactive=false] Checks to see if the JMS provider is up and running. This command is supported in remote mode only. OPTIONS
--user authorized domain application server administrative username. --password password to administer the domain application server. --host machine name where the domain application server is running. --port port number of the domain application server listening for administration requests. --passwordfile file containing the domain application server password. --secure if true, uses SSL/TLS to communicate with the domain application server. --terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well- formatted data for consumption by a script. Default is false. --echo setting to true will echo the command line statement on the standard output. Default is false. --interactive if set to true (default), only the required password options are prompted. Example 1: Using jms-ping asadmin> jms-ping --user admin --password adminadmin --host bluestar --port 4848 server1 JMS Ping Status=RUNNING EXIT STATUS
0 command executed successfully 1 error in executing the command asadmin-create-jmsdest(1AS), asadmin-delete-jmsdest(1AS), asadmin-list-jmsdest(1AS) J2EE 1.4 SDK March 2004 asadmin-jms-ping(1AS)
All times are GMT -4. The time now is 09:13 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy