12-21-2012
Just a first thought. Is the lo interface up?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: -
1 QNX host->Eth->1 SCO host
the SCO host is configured with it's IP
the QNX host is configured with another IP
both in the same domain, ie, 172.20.3.XX... (3 Replies)
Discussion started by: gavon
3 Replies
2. UNIX for Dummies Questions & Answers
Hello,
hi guys I don't know what is the problem with my NIC I can ping the Localhost (LOOPBACK) but when I run a scripts to check the NIC statuse it's shown the NIC DOWN sooo what could be the problem and what is the best way to start trouplshooting the NIC in SUN-SOLARIS.
Regards,
Karim
... (3 Replies)
Discussion started by: geoquest
3 Replies
3. UNIX for Dummies Questions & Answers
I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the
etc/tcp
etc/hosts
files which i did. still unable to ping.
i am getting a message unable to route to host.
I also have an error in my etc/tcp file on line... (1 Reply)
Discussion started by: pdoug76
1 Replies
4. UNIX for Dummies Questions & Answers
DEar all
i am receiving this error on start and then unable to ping
(dlpid): unable to open network adapter driver (/dev/mdi/e3h0)
what to do ? (2 Replies)
Discussion started by: sak900354
2 Replies
5. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
6. Solaris
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
Discussion started by: skiturn
2 Replies
7. IP Networking
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Discussion started by: skiturn
8 Replies
8. Solaris
Hi ALL,
I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network
bk (1 Reply)
Discussion started by: suresh_krish
1 Replies
9. Solaris
Hello,
Am unable to ping the Windows Box, from my Solaris Box.
They both are in same LAN, have the same IP Segments.
Windows IP :: 10.141.14.120
Solaris IP :: 10.141.14.11
Unable to get why isnt working out.... When using the command 'ping 10.141.14.120', it gives the error as 'ping:... (4 Replies)
Discussion started by: jayanto
4 Replies
10. IP Networking
Hello Everyone,
I have unable to run the default server with localhost in my Debian machine. While trying to run Django I get:
Error: That IP address can't be assigned-to.
error
While trying to run galaxy-dist I get this error:
socket.error: Cannot assign requested address
I can't telnet... (3 Replies)
Discussion started by: sachit adhikari
3 Replies
LEARN ABOUT DEBIAN
mrtg-ping-probe
MRTG-PING-PROBE(1) General Commands Manual MRTG-PING-PROBE(1)
NAME
mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher
DESCRIPTION
mrtg-ping-probe is a ping probe module for MRTG 2.x. It is used to monitor the round trip time and packet loss to networked devices. MRTG
uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.
mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.
Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission. Just imagine if 10,000 people decided to ping
your hosts! mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.
OPTIONS
To use mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
file, which is usually /etc/mrtg.conf.
Here's an example snippet: change the target name and IP address to suit your needs.
Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
MaxBytes[your.target.ping]: 100
AbsMax[your.target.ping]: 200
Options[your.target.ping]: gauge, growright
YLegend[your.target.ping]: ping time (ms)
ShortLegend[your.target.ping]: ms
Legend1[your.target.ping]: Maximum Round Trip Time in ms
Legend2[your.target.ping]: Minimum Round Trip Time in ms
Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
LegendI[your.target.ping]: Max:
LegendO[your.target.ping]: Min:
Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that you need
to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.
SEE ALSO
mrtg(1).
The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/
AUTHOR
This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).
April 14, 2003 MRTG-PING-PROBE(1)