Sponsored Content
Operating Systems Solaris Execute the ntpdate command only when NTP daemon is stopped? Post 302738903 by hombreopaco on Monday 3rd of December 2012 05:36:01 AM
Old 12-03-2012
fpmurphy is rigth, I'm not sure about all the NTP versions, but, in my experience, any time difference more than 5 minutes will produce a ntpd synchronization fail, it will back to the LOCAL time, so, if you have more than this difference, you must to do a ntpdate before to start the ntpd daemon.
This User Gave Thanks to hombreopaco For This Post:
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

NTPDATE Command help

I would like to setup date / time sync on Solaris 8 using the command ntpdate. How do I set it up? Thanks Mark (1 Reply)
Discussion started by: miredale
1 Replies

2. Solaris

How to use Ntpdate to slew the time?

Hi experts, I've a master server which sync to ntp time server daily by using xntpd daemon. Then my client servers will use ntpdate through cron job to synchronize the time hourly. (By using ntpupdate -s -B 'master server') My question is, now I'll need to synchronize to a oracle server which... (2 Replies)
Discussion started by: kenzoo
2 Replies

3. SCO

ntpdate problem in Unixware

Hi Guys, A weird problem. I have disabled ntpd daemon on a HP server and placed ntpdate in crontab instead and redirected the log to a file. This command in cron synchronizes the server with a local time server every 15 minutes. The weird part is that on 3 specific times (5:00 am, 10:00 am,... (2 Replies)
Discussion started by: Verifone
2 Replies

4. UNIX for Dummies Questions & Answers

how execute/visit a site using the cron daemon?

hi, i need to execute/visit a site to check if the site is up or not i have a server that have cron shedule that can execute a php file now how can i execute/visite a site using the same way as i execute a file? thanks a lot for your help :) (1 Reply)
Discussion started by: jasonx22
1 Replies

5. Shell Programming and Scripting

How to replace ntpdate

Hi there, Hi have a group of computers + a server (all debians) connected to each other on a LAN. For some reasons that I've not decided and that I can't change, the computers cannot connect to the net. Moreover, the server has no ntp service. Though, I need to find a way of setting all... (4 Replies)
Discussion started by: chebarbudo
4 Replies

6. Linux

ntp client/daemon sync

All, I need to write a script which can determine if my NTP client is X second off from the NTPD server time. I am looking for a crafty oneliner to calculate the time difference? (3 Replies)
Discussion started by: vada010
3 Replies

7. HP-UX

Setting up NTP HP-UX clients from solaris NTP server

Hi I wonder if its possible to setup NTP clients running HP-UX o.s. from a solaris 10 NTP server? FR (3 Replies)
Discussion started by: fretagi
3 Replies

8. Solaris

Is ntpdate command dependent on ntpd?

Hi, Could someone Please clarify me here: Is ntpdate command a part of ntpd, i mean does ntpdate command a dependent on ntpd? and can ntpdate be run in absence of ntpd service. (5 Replies)
Discussion started by: aksijain
5 Replies

9. Red Hat

Ntp client sync with local over ntp server

Hi, I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local? # ntpq -p ... (3 Replies)
Discussion started by: pjeedu2247
3 Replies

10. UNIX for Dummies Questions & Answers

Nohup Command gets status Stopped

Good Morning I need your help please, i tried to execute this script using nohup command but it gets in status stopped nohup ./SapInterfases.sh > SapInterfases.log & prodstg02$ jobs + Stopped(SIGTTOU) nohup ./SapInterfases.sh > SapInterfases.log & I check out log: $ more... (15 Replies)
Discussion started by: alexcol
15 Replies
NTPDATE(8)						    BSD System Manager's Manual 						NTPDATE(8)

NAME
ntpdate -- set the date and time via NTP SYNOPSIS
ntpdate [-bBdoqsuv] [-a key] [-e authdelay] [-k keyfile] [-o version] [-p samples] [-t timeout] [server ...] DESCRIPTION
ntpdate sets the local date and time by polling the Network Time Protocol (NTP) server(s) given as the server arguments to determine the cor- rect time. It must be run as root on the local host. A number of samples are obtained from each of the servers specified and a subset of the NTP clock filter and selection algorithms are applied to select the best of these. Note that the accuracy and reliability of ntpdate depends on the number of servers, the number of polls each time it is run and the interval between runs. ntpdate can be run manually as necessary to set the host clock, or it can be run from the host startup script to set the clock at boot time. This is useful in some cases to set the clock initially before starting the NTP daemon ntpd. It is also possible to run ntpdate from a cron script. However, it is important to note that ntpdate with contrived cron scripts is no substitute for the NTP daemon, which uses sophisti- cated algorithms to maximize accuracy and reliability while minimizing resource use. Finally, since ntpdate does not discipline the host clock frequency as does ntpd, the accuracy using ntpdate is limited. Time adjustments are made by ntpdate in one of two ways. If ntpdate determines the clock is in error more than 0.5 second it will simply step the time by calling the system settimeofday(2) routine. If the error is less than 0.5 seconds, it will slew the time by calling the system adjtime(2) routine. The latter technique is less disruptive and more accurate when the error is small, and works quite well when ntpdate is run by cron every hour or two. ntpdate will decline to set the date if an NTP server daemon (e.g., ntpd ) is running on the same host. When running ntpdate on a regular basis from cron as an alternative to running a daemon, doing so once every hour or two will result in precise enough timekeeping to avoid stepping the clock. If NetInfo support is compiled into ntpdate, then the server argument is optional if ntpdate can find a time server in the NetInfo configura- tion for ntpd COMMAND LINE OPTIONS
-a key Enable the authentication function and specify the key identifier to be used for authentication as the argument key ntpdate. The keys and key identifiers must match in both the client and server key files. The default is to disable the authentication function. -B Force the time to always be slewed using the adjtime() system call, even if the measured offset is greater than +-128 ms. The default is to step the time using settimeofday() if the offset is greater than +-128 ms. Note that, if the offset is much greater than +-128 ms in this case, that it can take a long time (hours) to slew the clock to the correct value. During this time. the host should not be used to synchronize clients. -b Force the time to be stepped using the settimeofday() system call, rather than slewed (default) using the adjtime() system call. This option should be used when called from a startup file at boot time. -d Enable the debugging mode, in which ntpdate will go through all the steps, but not adjust the local clock. Information useful for general debugging will also be printed. -e authdelay Specify the processing delay to perform an authentication function as the value authdelay , in seconds and fraction (see ntpd for details). This number is usually small enough to be negligible for most purposes, though specifying a value may improve timekeeping on very slow CPU's. -k keyfile Specify the path for the authentication key file as the string keyfile The default is /etc/ntp.keys. This file should be in the for- mat described in ntpd -o version Specify the NTP version for outgoing packets as the integer version , which can be 1 or 2. The default is 3. This allows ntpdate to be used with older NTP versions. -p samples Specify the number of samples to be acquired from each server as the integer samples , with values from 1 to 8 inclusive. The default is 4. -q Query only - don't set the clock. -s Divert logging output from the standard output (default) to the system syslog facility. This is designed primarily for convenience of cron scripts. -t timeout Specify the maximum time waiting for a server response as the value timeout , in seconds and fraction. The value is rounded to a mul- tiple of 0.2 seconds. The default is 1 second, a value suitable for polling across a LAN. -u Direct ntpdate to use an unprivileged port for outgoing packets. This is most useful when behind a firewall that blocks incoming traffic to privileged ports, and you want to synchronise with hosts beyond the firewall. Note that the -d option always uses unprivi- leged ports. -v Be verbose. This option will cause ntpdate string to be logged. FILES
/etc/ntp.keys encryption keys used by ntpdate. AUTHORS
David L. Mills (mills@udel.edu) BUGS
The slew adjustment is actually 50% larger than the measured offset, since this (it is argued) will tend to keep a badly drifting clock more accurate. This is probably not a good idea and may cause a troubling hunt for some values of the kernel variables tick and tickadj. BSD
January 28, 2010 BSD
All times are GMT -4. The time now is 11:58 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy