04-24-2012
@hedkandi
Were you running HP-UX when you issued those commands?
10 More Discussions You Might Find Interesting
1. Solaris
I have a bogus disk that keeps showing up as failed from vxdisk list
- - disk hpdg failed was:c2t0d11s2
There isnt any c2 devices on the system:
# ls /dev/dsk/c2*
/dev/dsk/c2*: No such file or directory
# ls /dev/rdsk/c2*
/dev/rdsk/c2*: No such file or... (3 Replies)
Discussion started by: kiem
3 Replies
2. AIX
Hello,
I've got 2 system disks (hdisk0 and hdisk1) in the mirror (RAID1) on AIX 5.3. Since the hdisk1 makes some troubles, we want to replace it with the new one. How can I disable this hdisk1 disk and prepare the mirror to use the new physical disk? As far as I know, I must remove disk from the... (3 Replies)
Discussion started by: Yac
3 Replies
3. Solaris
Hello once again seeking your help,
I have a mirrored disk and need to unmirror it to mount it as a new file system (/export) but could not find the correct steps to do it with out affecting the original disk.
can anybody point me out on how to get this done.
Thanks!! (3 Replies)
Discussion started by: AQG
3 Replies
4. AIX
Hi Experts,
I have configured A D40 Array. There is an faulty disk which is not part of an raid volume but shows fault in the diagnostics.
pdisk15 U0.1-P1-I1/Q1-W40AA83CC2400D
SSA160 Physical Disk Drive ( MB)
Is there a way to stop this... (2 Replies)
Discussion started by: vuppala360
2 Replies
5. Solaris
Hi,
Recently i came across a disk that seems to be faulty and need help. I have gathered some information by running below commands and any help on how to solve this will be great.
# uname –a
SunOS XYZ 5.7 Generic_106541-16 sun4u sparc SUNW,Ultra-4
#df -k
Filesystem kbytes used... (3 Replies)
Discussion started by: phanidhar6039
3 Replies
6. HP-UX
Requirement to remove a faulty mirrored disk from hp-ux LVM
<root@pdwp1s>/etc # vgdisplay -v /dev/vg00
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c2t0d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't... (9 Replies)
Discussion started by: Shirishlnx
9 Replies
7. HP-UX
Hello,
I'm new to this forum and as you will see from my question I'm new to UNIX as well.
One of our costumers has HP rx4640 running on UNIX with two 300GB hot-swappable disks that are mirrored. They reported to us that one of the disks is faulty and they want us to take care of it. Below is... (16 Replies)
Discussion started by: gjk
16 Replies
8. AIX
Hi
I have one of the disk missing in my NIMVG. My doubt is can I remove this hdisk2 online ? few of the file systems seems to be spread over 7 PV's. that's why i'm worried. Can someone suggest if I can replace this disk online. Also how to check if there is some data present in hdisk2 alone... (2 Replies)
Discussion started by: newtoaixos
2 Replies
9. Solaris
Hi Guys,
One of two disks in my solaris machine has failed, the name is disk0, this is SUN physical sparc machine
But I work remotely, so people working near that physical server are not that technical, so from OS command prompt can run some command to bink faulty disk at front panel of Server.... (9 Replies)
Discussion started by: manalisharmabe
9 Replies
10. UNIX for Beginners Questions & Answers
I plugged both power cables in both power supply. When I unplugged each power cable one by one, the SPARC T4-1 machine keep running. However, show faulty command shows below message. (I have also attached the picture of both power supply)
-> show faulty
Target ... (1 Reply)
Discussion started by: z_haseeb
1 Replies
LEARN ABOUT FREEBSD
color.4th
COLOR.4TH(8) BSD System Manager's Manual COLOR.4TH(8)
NAME
color.4th -- FreeBSD color-detection boot module
DESCRIPTION
The file that goes by the name of color.4th is a set of commands designed to simplify color logic. The commands of color.4th by themselves
are not enough for most uses. Please refer to the examples below for the most common situations, and to loader(8) for additional commands.
Before using any of the commands provided in color.4th, it must be included through the command:
include color.4th
This line is present in /boot/loader.4th file, so it is not needed (and should not be re-issued) in a normal setup.
The commands provided by it are:
loader_color? Returns FALSE if the loader_color environment variable is set to ``NO'' (case-insensitive) or ``0''. Otherwise
returns TRUE (unless booting serial).
The environment variables that effect its behavior are:
loader_color
If set to ``NO'' (case-insensitive) or ``0'', causes loader_color? to return FALSE, indicating to many modules that color
should not be used.
FILES
/boot/loader The loader(8).
/boot/color.4th color.4th itself.
/boot/loader.rc loader(8) bootstrapping script.
EXAMPLES
Standard i386 /boot/loader.rc:
Use color where applicable:
loader_color="YES"
SEE ALSO
loader.conf(5), loader(8), loader.4th(8)
HISTORY
The color.4th set of commands first appeared in FreeBSD 9.0.
AUTHORS
The color.4th set of commands was written by Devin Teske <dteske@FreeBSD.org>.
BSD
August 6, 2013 BSD