03-14-2012
Thanks for the replies.I found out with google that if you touch the power button twice after the boot bleep,that you will go straight to a ok prompt.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies
4. Solaris
FYI noob to here and sun blades...
I have a sun blade 100 and I can't get the cdrom to work. if i try using vold that doesn't seem to work either...maybe i'm not using it correctly.
Upon boot you can open/close the cdrom and it runs but after i'm logged in it won't open and i can't access it... (2 Replies)
Discussion started by: shaun138
2 Replies
5. Solaris
We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there.
We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies
6. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
7. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
8. Solaris
Hi everybody,
I'm having big troubles in installing Solaris 8 on a Sun Blade 150.
Here are some system specs:
Sun Blade 150 (UltraSPARC-IIe 550MHz)
RAM: 256MB
OBP 4.10.6 2003/06/06 12:30
POST 2.0.1 2001/08/23 17:13
When I try to boot from Solaris 8 CD with boot cdrom or... (10 Replies)
Discussion started by: Vortigern
10 Replies
9. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
10. Solaris
hi:)
i can't boot my sun server by iso solaris 10 sparc dvd that i did download from oracle site.
my hardware is sun T5220.
i receive these after running boot cdrom -s :
can't read disk lable
can't open disk lable package
ERROR: boot-read fail
whould u help me?
Please use CODE... (1 Reply)
Discussion started by: Arefdel
1 Replies
LEARN ABOUT OPENSOLARIS
gnome-power-preferences
gnome-power-preferences(1) User Commands gnome-power-preferences(1)
NAME
gnome-power-preferences - gnome power preferences GUI
SYNOPSIS
gnome-power-preferences [--help] [--verbose]
DESCRIPTION
gnome-power-preferences is a GUI configuration program. It enables you to configure your preferred desktop power management policies, e.g.
blank screen when lid is closed, hibernate system when battery power is low, suspend system when power button is pressed, or let CPU fre-
quency dynamically adjust based on process load. Then, these policies are enforced by gnome-power-manager(1).
OPTIONS
This program follows the usual command line syntax, with long options starting with two dashes (`-'). A summary of options is included
below.
--help Show summary of options.
--verbose Show extra debugging.
EXAMPLES
Example 1: Launching gnome-power-preferences with the display of extra debugging messages.
example% gnome-power-preferences --verbose
EXIT STATUS
The following exit values are returned:
0 Application exited successfully
>0 Application exited with failure
FILES
The following files are used by this application:
/usr/bin/gnome-power-preferences
Executable for gnome power preferences GUI
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWgnome-power-manager |
+-----------------------------+-----------------------------+
|Interface stability |Volatile |
+-----------------------------+-----------------------------+
SEE ALSO
gnome-power-manager(1), gnome-power-statistics(1), attributes(5)
NOTES
This manual page was written by Oliver Grawert ogra@ubuntu.com for the Debian system.
Updated by Simon Zheng, Sun Microsystems Inc., 2008.
SunOS 5.11 18 Feb 2008 gnome-power-preferences(1)