Sponsored Content
Operating Systems Solaris Sun Blade 150 wont boot off cdrom Post 302607434 by hicksd8 on Wednesday 14th of March 2012 11:51:24 AM
Old 03-14-2012
You need to get to a "ok" prompt somehow.

The machine is obviously configured to boot from the network. Are you sure that it has a hard drive in it?

to get into install mode you either attach a console keyboard and screen and then all output goes to vga, or you detach console keyboard and screen and use serial interface only (eg. vt100).

I don't know the Blade 150 very well but I'd say that if you had a Sun keyboard you could type STOP-A to interrupt it, or if you had a serial keyboard attached you could type Ctrl-Break.

I don't think that you've got the right kit to do either.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Memory upgrade Sun Blade 150

I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system." Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies

2. UNIX for Dummies Questions & Answers

Please help to configure Sun Blade 150 workstation

Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies

3. Solaris

Sun Blade 150 - I can't hook up extra drives

I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies

4. Solaris

Sun Blade 100 cdrom problems...

FYI noob to here and sun blades... I have a sun blade 100 and I can't get the cdrom to work. if i try using vold that doesn't seem to work either...maybe i'm not using it correctly. Upon boot you can open/close the cdrom and it runs but after i'm logged in it won't open and i can't access it... (2 Replies)
Discussion started by: shaun138
2 Replies

5. Solaris

Jumpstart Solaris 8 on Sun Blade 150 Hangs

We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there. We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies

6. Solaris

Sun Blade 150 not a Sun?

I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05. I have just noticed /bin/sun now returns false, rather than true. See below. $ uname -a SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100 $ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies

7. Solaris

Sun Blade 150 will not boot off harddrive after install of solaris 10

Hello, I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies

8. Solaris

Cannot install or run Solaris 8 on Sun Blade 150

Hi everybody, I'm having big troubles in installing Solaris 8 on a Sun Blade 150. Here are some system specs: Sun Blade 150 (UltraSPARC-IIe 550MHz) RAM: 256MB OBP 4.10.6 2003/06/06 12:30 POST 2.0.1 2001/08/23 17:13 When I try to boot from Solaris 8 CD with boot cdrom or... (10 Replies)
Discussion started by: Vortigern
10 Replies

9. Solaris

Execution problems with sun blade 150

hello i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies

10. Solaris

I can't boot my Sun T5220 server from cdrom.

hi:) i can't boot my sun server by iso solaris 10 sparc dvd that i did download from oracle site. my hardware is sun T5220. i receive these after running boot cdrom -s : can't read disk lable can't open disk lable package ERROR: boot-read fail whould u help me? Please use CODE... (1 Reply)
Discussion started by: Arefdel
1 Replies
UNICODE_START(1)					      General Commands Manual						  UNICODE_START(1)

NAME
unicode_start - put keyboard and console in unicode mode SYNOPSIS
unicode_start [font [umap]] DESCRIPTION
The unicode_start command will put the keyboard and console into Unicode (UTF-8) mode. For the keyboard this means that one can attach 16-bit U+xxxx values to keyboard keys using loadkeys(1), and have these appear as UTF-8 input to user programs. Also, that one can type hexadecimal Alt-xxxx using the numeric keypad, and again produce UTF-8. For the console this means that the kernel expects UTF-8 output from user programs, and displays the output accordingly. The parameter font is a font that is loaded. It should have a built-in Unicode map, or, if it hasn't, such a map can be given explicitly as second parameter. When no font was specified, the current font is kept. NOTE
Unicode mode is a parameter with a value per virtual console. However, usually the font and keymap is common to all consoles. SEE ALSO
dumpkeys(1), kbd_mode(1), loadkeys(1), unicode_stop(1), utf-8(7), setfont(8) 3 Feb 2001 UNICODE_START(1)
All times are GMT -4. The time now is 07:25 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy