|
|
Sponsored Content
Special Forums
Hardware
Filesystems, Disks and Memory
Can't repair super block, bad magic number
Post 302562541 by dallasw1983 on Friday 7th of October 2011 08:49:56 AM
10-07-2011
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am running mandrake 8.2 and when booting I get the message:
e2fschk: Bad magic number in super-block while trying to open /dev/hda8.
The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and really contains a valid an ext2 filesystem (and... (1 Reply)
Discussion started by: Jay
1 Replies
2. UNIX for Advanced & Expert Users
Hi,
when installing a piece of third part software I get the error "Bad magic number" at one point when it tries to use libraries from the bea tuxedo server. Am I correct that this means that the software is expecting 32bit while I'm on 64bit? Is there a way around it or can it only be solved... (5 Replies)
Discussion started by: rein
5 Replies
3. Filesystems, Disks and Memory
Dear All,
i have a SCSI hard disk drive i'm installing on it solaris 5 and the workstation is sun sparc, i made an image of this H.D using Norton Ghost 6, so i took off the SCSI H.D from the sun workstation and put it on a Compaq server then i booted the server from the Norton Ghost floppy disk... (0 Replies)
Discussion started by: wesweshahaha
0 Replies
4. HP-UX
Error received when I tried to restore a blank disk with an 'auto recovery' DDS tape via HP-UX recovery system 2.0 onto a 1Gb SCSI. I assumed it would do the setup, wrong. Could someone tell me the procedure to initial disk for recovering files using cpio. The system is a HP-UX 9.04 version on a... (1 Reply)
Discussion started by: admin wanabee
1 Replies
5. Filesystems, Disks and Memory
I had a power outage a day ago and when the power came back on my FreeBSD 4.6 webserver had problems. It said it was unable to mount /var and made me start in single user mode and said to run fsck MANUALY. So i did and this is now what i get.
www# fsck /dev/ad0s1e
** /dev/ad0s1e
BAD SUPER... (4 Replies)
Discussion started by: matthewbane
4 Replies
6. Solaris
I want mount a disk. I have this error. I'm trying to correct with the superblock but i have the same error. Look my procedure.
bash-2.03# fsck -F ufs /dev/rdsk/c0t1d0s0
Alternate super block location: 9423392.
** /dev/rdsk/c0t1d0s0
BAD SUPER BLOCK: MAGIC NUMBER WRONG
USE AN ALTERNATE... (1 Reply)
Discussion started by: simquest
1 Replies
7. UNIX for Advanced & Expert Users
Hello All,
(RHEL4)
Few weeks ago I had posted a message in this forum about the problem I had when I replaced my two scsi disks and tried rebuild raid1 array.
I somehow managed to up the system with working raid1 array.
But the main problem persisted..
i.e when I reboot the system, mounting... (0 Replies)
Discussion started by: ravinandan
0 Replies
8. Filesystems, Disks and Memory
Whenever i run,
# fsck -F ufs /dev/dsk/c0t0d0s7
The following error prompt out:-
** /dev/dsk/c0t0d0s7
BAD SUPER BLOCK: MAGIC NUMBER WRONG
USE AN ALTERNATE SUPER-BLOCK TO SUPPLY NEEDED INFORMATION;
eg. fsck -o b=#
where # is the alternate super block. SEE fsck_ufs(1M).
... (3 Replies)
Discussion started by: beginningDBA
3 Replies
9. Solaris
I'll keep it fairly straight forward. I work with a Solaris server and magically today it decided to take a dump on me. At first it give a long list of files that couldn't be acessed before terminating the boot process and returning to the 'ok' prompt. Booting in single-user mode allowed me to run... (4 Replies)
Discussion started by: Aon
4 Replies
10. Solaris
So we have a new to us v240 server with no OS installed. It has an outdated version of OB and ALOM so before we install the OS we want to update both. We have a DVD with the latest OB patch burned on it.
We do the boot cdrom command but receive the Bad Magic Number Error. Does an OS need to... (2 Replies)
Discussion started by: dunkpancakes
2 Replies
LEARN ABOUT XFREE86
pvscan
PVSCAN(8) System Manager's Manual PVSCAN(8) NAME
pvscan - scan all disks for physical volumes SYNOPSIS
pvscan [-d|--debug] [-h|--help] [-v|--verbose] [--version] [--ignorelockingfailure] [-e|--exported] [-n|--novolumegroup] [-s|--short] [-u|--uuid] pvscan [-d|--debug] [-h|--help] --cache [--major major --minor minor | DevicePath ] ... DESCRIPTION
pvscan scans all supported LVM block devices in the system for physical volumes. OPTIONS
See lvm(8) for common options. -e, --exported Only show physical volumes belonging to exported volume groups. -n, --novolumegroup Only show physical volumes not belonging to any volume group. -s, --short Short listing format. -u, --uuid Show UUIDs (Uniform Unique Identifiers) in addition to device special names. --cache [ --major major --minor minor | DevicePath ] ... Scan one or more devices and instruct the lvmetad daemon to update its cached state accordingly. Called internally by udev rules. All devices listed explicitly are processed regardless of any device filters set in lvm.conf. SEE ALSO
lvm(8), pvcreate(8), pvdisplay(8) Sistina Software UK LVM TOOLS 2.02.95(2) (2012-03-06) PVSCAN(8)