|
|
Sponsored Content
Operating Systems
Linux
Red Hat
Device eth0 issue
Post 302539957 by mark54g on Tuesday 19th of July 2011 08:17:16 AM
07-19-2011
|
|
5 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI,
When I do 'service network restart' , I am getting the following error.
"3c501 device eth0 does not seem to be present, delaying initialization"
Can any one suggest me the cause/solution for this?
When I do 'lspci' it is showing the ehternet card as
" Ethernet controller"Marvell... (2 Replies)
Discussion started by: praveen_b744
2 Replies
2. AIX
I need upgrade firmware for the device of p570, when I go to IBM FIX download website, there are a lot of device of p570 listed. How can I know what device I have on my p570? (4 Replies)
Discussion started by: rainbow_bean
4 Replies
3. Solaris
In my 2 node cluster (sun cluster3.2) running on x86 VMs. One of my nodes VM1 does not have the global devices populated due to which i cannot failover my file system to node VM1 , what could be the reason for this and how can i rectify it ?
VM1:/>cd /dev/global
-bash: cd: /dev/global: No... (1 Reply)
Discussion started by: fugitive
1 Replies
4. Red Hat
Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
5. HP-UX
Hi,
Unable to make tape backup, please help.
/opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00
* Creating local directories for configuration files and archive.
======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery.
(Mon... (4 Replies)
Discussion started by: anuragr
4 Replies
LEARN ABOUT DEBIAN
plucker-prc-install
plucker-prc-install(1) General Commands Manual plucker-prc-install(1) NAME
plucker-prc-install - fetch and install Plucker viewer application on a Palm pilot SYNOPSIS
plucker-prc-install [options] DESCRIPTION
This manual page documents briefly the plucker-prc-install command. This manual page was written for the Debian distribution because this program was created for the Debian package. plucker-prc-install is a program that fetches and installs the Plucker viewer application. The program uses wget to get the .tar.bz2 archive from the Web. You need to be connected to the Internet and have wget working correctly in order to use this program. You may have to configure the environment variable http_proxy. You can take a look at the lynx command manpage to get information about http_proxy. The program tries to use the correct language version of the viewer according to the environment variable LANG. The program then uses either gpilot-install-file or pilot-xfer to transfer the three .prc files to the Palm pilot. With pilot-link 0.12.x it is mandatory to provide a port to use. plucker-prc-install first use the value of the PILOTPORT environment variable. If PILOTPORT is not defined it uses /dev/pilot. If the file /dev/pilot does not exist it uses usb:. OPTIONS
This program follows the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. --nohires installs the low-resolution version of the Plucker viewer. If you are using a Palm with a 160x160 screen (Palm m500-series and ear- lier) you can save approximately 90 KB by installing the low-resolution version of the viewer. Note that the hires version will still work on older Palms, but will just take up unnecessary space. -h, --help Show summary of options. -v, --version Show version of program. SEE ALSO
pilot-xfer(1), wget(1), gpilot-install-file(1), lynx(1). AUTHOR
This manual page was written by Ludovic Rousseau <rousseau@debian.org>, for the Debian GNU/Linux system (but may be used by others). August 22, 2005 plucker-prc-install(1)