All
Please help, i will telnet to router to obain the ping status and compare, if higher than normal latency, i will have further action..
if i do the telent and in perl script then ....
e.g the result i obtain from the router will be =' Success rate is 100 percent (5/5), round-trip... (4 Replies)
Somewhat long story:
I have a simple Perl CGI script that uses Expect to Telnet to a device and grab some data, and then spits it back to Perl for display on the Webpage.
This works for many devices I've tried, but one device just fails, it keeps rejecting the password on this device, only... (1 Reply)
This Expect script provides expect with a list of IP addresses to Cisco IPS sensors and commands to configure Cisco IPS sensors. The user, password, IP addresses, prompt regex, etc. have been anonymized. In general this script will log into the sensors and send commands successfully but there are... (1 Reply)
Hi Experts,
I am using perl to telnet on cisco boxes. We have this stupid cisco node which does not support "terminal Length0" command.
Since I am using Net::Telnet and capturing output with
@output = $telnet->cmd('cmd');
Say
@output = $telnet->cmd('show version');
Now problem... (2 Replies)
I am writing perl script to configure Cisco device but Variables inside Net::Telnet::Cisco Module doesn't work and passed to device without resolving.
Please advise.
here is a sample of script:
use Net::Telnet::Cisco;
$device = "10.14.199.1";
($o1, $o2, $o3, $o4) = split(/\./,$device);... (5 Replies)
Hi all,
I use a bash script which use expect to connect throught ssh and run command on a cisco router. The ssh connection with expect work fine, but the first command on the cisco router failed,
I try to run the command in error by hand and it work fine... :(
the first part of the script... (2 Replies)
Hi all
i have little problem finding solution about simple telnet script .... i have 250 routers and on some i have different password and on some they ask just for password no username. So for example 1,2,3 have username and password (user,password) 4, and 5 have different username and password... (0 Replies)
I know there are better ways to do this.
I prefer snmp. I do not have the proper perl modules loaded on the platorm. Snmp isnt loaded on the platform. Telnet is not an option. I need to write an expect script to pull cisco equipment configs.
The following code is executed once I gain... (0 Replies)
HI all
i need to connect to about 900 cisco routers and switch to do some configs changes. the issue i am having is that half the devices have one set of username and password and the other half have another username and password. From expect or bash script i can ssh into a device and make... (0 Replies)
Discussion started by: quintin
0 Replies
LEARN ABOUT LINUX
ct_ftp
ct_ftp(3erl) Erlang Module Definition ct_ftp(3erl)NAME
ct_ftp - FTP client module (based on the FTP support of the INETS application).
DESCRIPTION
FTP client module (based on the FTP support of the INETS application).
DATA TYPES
connection() = handle() | target_name() (see module ct) :
handle() = handle() (see module ct_gen_conn) :
Handle for a specific ftp connection.
EXPORTS
cd(Connection, Dir) -> ok | {error, Reason}
Types Connection = connection()
Dir = string()
Change directory on remote host.
close(Connection) -> ok | {error, Reason}
Types Connection = connection()
Close the FTP connection.
delete(Connection, File) -> ok | {error, Reason}
Types Connection = connection()
File = string()
Delete a file on remote host
get(KeyOrName, RemoteFile, LocalFile) -> ok | {error, Reason}
Types KeyOrName = Key | Name
Key = atom()
Name = target_name() (see module ct)
RemoteFile = string()
LocalFile = string()
Open a ftp connection and fetch a file from the remote host.
RemoteFile and LocalFile must be absolute paths.
The config file must be as for put/3.
See also: put/3 .
ls(Connection, Dir) -> {ok, Listing} | {error, Reason}
Types Connection = connection()
Dir = string()
Listing = string()
List the directory Dir.
open(KeyOrName) -> {ok, Handle} | {error, Reason}
Types KeyOrName = Key | Name
Key = atom()
Name = target_name() (see module ct)
Handle = handle()
Open an FTP connection to the specified node.
You can open one connection for a particular Name and use the same name as reference for all subsequent operations. If you want the
connection to be associated with Handle instead (in case you need to open multiple connections to a host for example), simply use
Key , the configuration variable name, to specify the target. Note that a connection that has no associated target name can only be
closed with the handle value.
put(KeyOrName, LocalFile, RemoteFile) -> ok | {error, Reason}
Types KeyOrName = Key | Name
Key = atom()
Name = target_name() (see module ct)
LocalFile = string()
RemoteFile = string()
Open a ftp connection and send a file to the remote host.
LocalFile and RemoteFile must be absolute paths.
If the target host is a "special" node, the ftp address must be specified in the config file like this:
{node,[{ftp,IpAddr}]}.
If the target host is something else, e.g. a unix host, the config file must also include the username and password (both strings):
{unix,[{ftp,IpAddr},
{username,Username},
{password,Password}]}.
recv(Connection, RemoteFile) -> ok | {error, Reason}
Fetch a file over FTP.
The file will get the same name on the local host.
See also: recv/3 .
recv(Connection, RemoteFile, LocalFile) -> ok | {error, Reason}
Types Connection = connection()
RemoteFile = string()
LocalFile = string()
Fetch a file over FTP.
The file will be named LocalFile on the local host.
send(Connection, LocalFile) -> ok | {error, Reason}
Send a file over FTP.
The file will get the same name on the remote host.
See also: send/3 .
send(Connection, LocalFile, RemoteFile) -> ok | {error, Reason}
Types Connection = connection()
LocalFile = string()
RemoteFile = string()
Send a file over FTP.
The file will be named RemoteFile on the remote host.
type(Connection, Type) -> ok | {error, Reason}
Types Connection = connection()
Type = ascii | binary
Change file transfer type
AUTHORS
<>
common_test 1.5.3 ct_ftp(3erl)