Sponsored Content
Special Forums Hardware Slackware 13.1 can't configure two network cards Post 302447930 by semash! on Tuesday 24th of August 2010 05:25:47 PM
Old 08-24-2010
Hey Corona688,

You were right, the driver '8139too' was blacklisted from modprobe, i don't know the reason. I commented ('#') it and rebooted, and i got it working. with some issues, but working. (Now there's no 'eth0' device, but 'eth1' and 'eth2').

Thank you very much.
 

10 More Discussions You Might Find Interesting

1. UNIX Desktop Questions & Answers

Help needed to configure GUI with Slackware 7 on an IBM Thinkpad Laptop

I am using Slackware 7 on my IBM Thinkpad. I am unable to configure it to display a graphical environment. Typing startx usually generates a few errors. The system, however, does boot into the shell environment without any issues or problems. I have been able to setup Slackware 7 successfully... (2 Replies)
Discussion started by: adrienb
2 Replies

2. UNIX for Dummies Questions & Answers

SCO Unix and Two Network Cards

Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies

3. Solaris

Disable Network cards under boot Prom

Hi, I'm looking for a command to be able to disable a network card under the boot PROM. I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0). Thanks, Fabien (6 Replies)
Discussion started by: unclefab
6 Replies

4. Solaris

How to List all Network cards

Hi, I'm looking for a command to be able to list all my network cards available on my server. With the command "ifconfig - a", I can only see to configured network card(s) Any idea ? :confused: Thanks a lot for your help, Fabien (5 Replies)
Discussion started by: unclefab
5 Replies

5. AIX

Load balancing across network cards

The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Discussion started by: johnf
4 Replies

6. Solaris

How to find network cards available ...

Hi all, I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output. Today, this server is using the on board network connection (Ce0). How can I find the other... (7 Replies)
Discussion started by: unclefab
7 Replies

7. Solaris

qfe errors and network cards

Hi All, Hope you are all doing good. In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies

8. Solaris

Network cards - Routing

Hi all I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem. So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies

9. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

10. Slackware

How configure micromax bsnl 3G modem in KPPP on slackware 13.1

How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under /dev/sr1 iso9660 /media/modem and in lsusb command add following information: Bus 001 Device 020: ID 1c9e:f000 now i follow these steps for usb switch to modem usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies
XI(4)							   BSD Kernel Interfaces Manual 						     XI(4)

NAME
xi -- Xircom CreditCard Ethernet device driver SYNOPSIS
xi* at xirc? Configuration of PHYs may also be necessary. See mii(4). DESCRIPTION
The xi driver provides support for the Xircom CreditCard family of PCMCIA Ethernet adapters. Supported cards include: Xircom CreditCard Ethernet II Xircom CreditCard 10/100 Ethernet Xircom RealPort 10/100 Ethernet + Modem (Ethernet function only) Intel EtherExpress Pro/100 Compaq Netelligent 10/100 Cards which should work, but have not been confirmed include: Xircom RealPort Ethernet Xircom RealPort 10/100 Ethernet Some Xircom Ethernet products are supported by the tlp(4) driver. MEDIA SELECTION
Media selection is done using ifconfig(8) using the standard ifmedia(4) mechanism. Refer to those manual pages for more information. SEE ALSO
ifmedia(4), mii(4), netintro(4), pcmcia(4), tlp(4), xirc(4), ifconfig(8) HISTORY
The xi device driver appeared in NetBSD 1.5. BUGS
The driver suffers from poor performance. Even with the 10/100 cards, do not expect more than ~450KB/s. Some 10/100 cards may not autonego- tiate reliably and require manual media selection. The Xircom multifunction cards which contain both Ethernet and modem interfaces are known to have problems. This is due to the card not reporting itself correctly as a multifunction card. BSD
June 1, 2007 BSD
All times are GMT -4. The time now is 07:28 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy