program.sh is working for me.
Anything else doesn't, no errors. I have tried this exhaustively. I think I'll just give up cause its driving me nuts.
The actual scripts I wrote are much longer. It didn't work for them, and when I narrowed it down this was the main problem.
---------- Post updated at 09:21 AM ---------- Previous update was at 08:34 AM ----------
Okay, so my fault here I over simplified my example in OP.
This is more of what I'm doing which for the line previous to the send_nsca binary program is not working:
in shell:
Code:
echo "host,log,0,message" | program_below.sh
program:
Code:
while read -r line; do
STRING=$line
echo $STRING > /usr/local/nagios/syslog/debug #and I see no output in debug file
echo $STRING | /usr/local/nagios/libexec/send_nsca -H 192.168.93.55 -d ',' -c /usr/local/nagios/etc/send_nsca.cfg #this works
done
HELP!!! LOL
---------- Post updated at 10:27 AM ---------- Previous update was at 09:21 AM ----------
These are all working, my bad, but for some reason they didn't before.
Solved the problem.
I am using syslog-ng program() as a destination for a log.
Apparently, the problem has to do with the absolute path in the script. I'm guessing if calling with program() it leaves the directory that script is called from, so the absolute path is necessary. Either way, it works now to:
absolute_path/debug.log
Thanks for the response, hours upon hours again wasted for nothing, I will ALWAYS freaken add an absolute path to every line of every script from now on. Lesson learned.
Last edited by timber333; 06-13-2010 at 09:40 AM..
STEP 1
# Set variable
FILE=/tmp/mainfile
SEARCHFILE =/tmp/searchfile
# THIS IS THE MAIN FILE.
cat /tmp/mainfile
Interface Ethernet0/0 "outside", is up, line protocol is up
Hardware is i82546GB rev03, BW 100 Mbps
Full-Duplex(Full-duplex), 100 Mbps(100 Mbps)
MAC address... (6 Replies)
I am using the while-loop to read a file.
The file has lines with null-terminated strings (words, actually.)
What I have by that reading - just a first word up to '\0'!
I need to have whole string up to 'new line' - (LF, 10#10, 16#A)
What I am doing wrong?
#make file 'grb' with... (6 Replies)
Hi ,
I am trying to write an shell, which reads a text file (from a location) having a list of numbers of strictly 5 digits only ex: 33144
Now my script will check :
1) that each entry is only 5 digits & numeric only, no alphabets, & its not empty.
2)then it executes a shell script called... (8 Replies)
Hi All,
I'm trying to figure out which are the trusted-ips and which are not using a script file.. I have a file named 'ip-list.txt' which contains some ip addresses and another file named 'trusted-ip-list.txt' which also contains some ip addresses. I want to read a line from... (4 Replies)
Hi all
I have spent half a day trying to create a shell script which reads a configuration file on a line by line basis.
The idea of the file is that each will contain server information, such as IP address and various port numbers. The line could also be blank (The file is user created). Here... (1 Reply)
Hello,
I need a program that read a file line by line and prints out lines 1, 2 & 3 after an empty line... An example of entries in the file would be:
SRVXPAPI001 ERRO JUN24 07:28:34 1775
REASON= 0000, PROCID= #E506 #1065: TPCIPPR, INDEX= 003F
... (8 Replies)
Hi All,
Am trying to write wrapper shell/bash script on a utility tool for which i need to pass 2 files as arugment to execute utility tool.
Wraper script am trying is to do with above metion 2 files.
utility tool accepts :
a. userinfo file : which contains username
b. item file : which... (2 Replies)
Hi all,
I have a log file say Test.log that gets updated continuously and it has data in pipe separated format. A sample log file would look like:
<date1>|<data1>|<url1>|<result1>
<date2>|<data2>|<url2>|<result2>
<date3>|<data3>|<url3>|<result3>
<date4>|<data4>|<url4>|<result4>
What I... (3 Replies)
Heyas
I'm trying to read/display a file its content and put borders around it (tui-cat / tui-cat -t(ypwriter).
The typewriter-part is a 'bonus' but still has its own flaws, but thats for later.
So in some way, i'm trying to rewrite cat using bash and other commands.
But sadly it fails on... (2 Replies)
Hello,
I'm works on Ubuntu server
My goal : I would like to read file line per line, but i want to started at the end of file.
Currently, I use instructions :
while read line;
do
COMMAND
done < /var/log/apache2/access.log
But, the first line, i don't want this. The file is long... (5 Replies)
Discussion started by: Fuziion
5 Replies
LEARN ABOUT FREEBSD
service
SERVICE(8) BSD System Manager's Manual SERVICE(8)NAME
service -- control (start/stop/etc.) or list system services
SYNOPSIS
service -e
service -R
service [-v] -l | -r
service [-v] <rc.d script> start|stop|etc.
DESCRIPTION
The service command is an easy interface to the rc.d system. Its primary purpose is to start and stop services provided by the rc.d scripts.
When used for this purpose it will set the same restricted environment that is in use at boot time (see below). It can also be used to list
the scripts using various criteria.
The options are as follows:
-e List services that are enabled. The list of scripts to check is compiled using rcorder(8) the same way that it is done in rc(8), then
that list of scripts is checked for an "rcvar" assignment. If present the script is checked to see if it is enabled.
-R Restart all enabled local services.
-l List all files in /etc/rc.d and the local startup directories. As described in rc.conf(5) this is usually /usr/local/etc/rc.d. All
files will be listed whether they are an actual rc.d script or not.
-r Generate the rcorder(8) as in -e above, but list all of the files, not just what is enabled.
-v Be slightly more verbose
ENVIRONMENT
When used to run rc.d scripts the service command sets HOME to / and PATH to /sbin:/bin:/usr/sbin:/usr/bin which is how they are set in
/etc/rc at boot time.
EXIT STATUS
The service utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
The following are examples of typical usage of the service command:
service named status
service -rv
The following programmable completion entry can be use in bash(1) for the names of the rc.d scripts:
_service () {
local cur
cur=${COMP_WORDS[COMP_CWORD]}
COMPREPLY=( $( compgen -W '$( service -l )' -- $cur ) )
return 0
}
complete -F _service service
SEE ALSO bash(1) (ports/shells/bash), rc.conf(5), rc(8), rcorder(8)HISTORY
The service utility first appeared in FreeBSD 7.3.
AUTHORS
This manual page was written by Douglas Barton <dougb@FreeBSD.org>.
BSD December 11, 2012 BSD
06-13-2010
