03-25-2010
Serial connection.
Have you tried troubleshooting using the serial port? You might get more information from there instead of a monitor and keyboard. It certainly sounds like you have some kind of hardware problem. If you dont know how to serially connect, then try using a minimum configuration of the Ultra 10 and see if you can narrow it down to a component. Check out the info below and good luck.
http://dlc.sun.com/pdf//805-7764-12/805-7764-12.pdf
10 More Discussions You Might Find Interesting
1. Solaris
am wonder wich sun computer is better, a sun ultra or sun sparkstation, and what is the difference (7 Replies)
Discussion started by: nobody
7 Replies
2. Solaris
I'm running solaris 2.5.1. My main development server is DEAD, i can't even boot off the cdrom, it powers up, acts like it is starting the boot process but then says cannot find boot device. I've done the search here on this site and saw the other posts, but at the ok prompt it won't even let me... (3 Replies)
Discussion started by: kymberm
3 Replies
3. Solaris
I just was given an Ultra 60 that I'm trying to get started so that I can re-load the system with Solaris 10. I can't seem to get the system to boot past the initial memory check. I've tried to do an Stop-A to get to the eeprom, but can't do that. My next step is to try to send a break from the... (0 Replies)
Discussion started by: zosojohnny
0 Replies
4. AIX
Hello:
NOOB here. I attempted to use smit mkcd. Failed on first attempt, not enough space. 2nd attempt tried to place iso on /usr, not enough space there. Cleanup ran for about 5 minutes after aborting. Now AIX won't boot. LCD display on 7029-6E3 says: 0517 MOUNT /USR. Attempted to boot from CD... (11 Replies)
Discussion started by: bbird
11 Replies
5. Solaris
Hi all - I have an issue with our (way old) single processor SunFire 280R, running Solaris 9.0.4.
It won't boot even after multiple power cycles. There was a power outage last week end in the computer room, so this might have to do.
In normal boot mode, the screen shows a single line :
... (5 Replies)
Discussion started by: bostella
5 Replies
6. Solaris
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies
7. Solaris
Hi,
I just got a new Ultra 5 and replaced the CD-ROM with an LG DVD-ROM (approved and listed in Sun HCL). Got the DVD-ROM installed to install Solaris 10. Im just learning and new to Solaris installation.
When I insert a Solaris 10 DVD I see that it gets mounted and File Manager opens and... (8 Replies)
Discussion started by: greypilgrim
8 Replies
8. Solaris
I am trying to get an old Ultra 45 to boot and it is stuck in a loop. I cannot get anything to come up on a monitor, so when I hook up a serial connection to the TTYa interface I see the following output:
@(#)OBP 4.21.2 2005/12/22 17:17 Sun Ultra 45 Workstation
Clearing TLBs
Loading... (0 Replies)
Discussion started by: Madrox72
0 Replies
9. UNIX for Beginners Questions & Answers
Hi all,
I've got a Sun ultra 30 workstation. the Nvram battery died so I replaced it. I reprogrammed the mac address using the mlpl command all that so it booted without error. But for some reason I was trying to boot via the network. So I did a STOP A and boot disk1 which is the alias for my SCSI... (2 Replies)
Discussion started by: robbo007
2 Replies
10. Solaris
Hi all,
I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET
Thanks,
Rob (3 Replies)
Discussion started by: robbo007
3 Replies
LEARN ABOUT CENTOS
gnutls_url_is_supported
gnutls_url_is_supported(3) gnutls gnutls_url_is_supported(3)
NAME
gnutls_url_is_supported - API function
SYNOPSIS
#include <gnutls/gnutls.h>
int gnutls_url_is_supported(const char* url);
ARGUMENTS
const char* url
A PKCS 11 url
DESCRIPTION
Check whether url is supported. Depending on the system libraries GnuTLS may support pkcs11 or tpmkey URLs.
RETURNS
return non-zero if the given URL is supported, and zero if it is not known.
SINCE
3.1.0
REPORTING BUGS
Report bugs to <bug-gnutls@gnu.org>.
General guidelines for reporting bugs: http://www.gnu.org/gethelp/
GnuTLS home page: http://www.gnu.org/software/gnutls/
COPYRIGHT
Copyright (C) 2012 Free Software Foundation, Inc..
Copying and distribution of this file, with or without modification, are permitted in any medium without royalty provided the copyright
notice and this notice are preserved.
SEE ALSO
The full documentation for gnutls is maintained as a Texinfo manual. If the info and gnutls programs are properly installed at your site,
the command
info gnutls
should give you access to the complete manual. As an alternative you may obtain the manual from:
http://www.gnu.org/software/gnutls/manual/
gnutls 3.1.15 gnutls_url_is_supported(3)