Sponsored Content
Full Discussion: iLO configuration
Operating Systems HP-UX iLO configuration Post 302397674 by sijocg on Tuesday 23rd of February 2010 12:25:01 AM
Old 02-23-2010
iLO configuration

how to set IP for iLO in HP server first time


thanks to all
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Xhost and ILO

I have an application that requires me to disable the restricted access to the X Server libraries by issuing the 'Xhost +' command from a Console Window. It is important that this command is run from the Console Window and not a Terminal Window otherwise the system complains that DISPLAY is not... (0 Replies)
Discussion started by: jimthompson
0 Replies

2. Solaris

HP iLO virtual serial port

Greetings All, If someone/anyone reading this post has had success setting up and configuring HP iLO2 CLI virtual serial port for Solaris...please tell how. I'm trying to get a remote console to an HP DL385 server via iLO2 and ssh. The server is running Solaris 10 (11/06), patched to... (1 Reply)
Discussion started by: alias.256
1 Replies

3. HP-UX

iLo RBSU

Hi, I wanted to setup a ilo for an HP 9000 rp 8420 server. Can anyone have an idea on it? (1 Reply)
Discussion started by: gunnervarma
1 Replies

4. Linux

Findout iLO type installed in a machine

I have to write Linux script to findout what kind of ilo is been installed in the given ip address either ilo/LO100 or no device found. IP address will be given in the command line of the script. -> With out log on to the ip address, should get the ilo type installed in that machine. 1. I... (1 Reply)
Discussion started by: skmdu
1 Replies

5. Solaris

T5220 ILO not saving static IP

I have a brand new T5220 and I'm trying to configure the ILOM port with a static Ip address via the Serial Management port. I log on as "root" and then enter the commands ( see below) to config the port. When I enter the last command which is " set /SP/network commitpending=true", which I... (9 Replies)
Discussion started by: danfall4
9 Replies

6. Hardware

Reset ILO password

HI Guys I have forgot my ILO password for REDHAT Linux, Its Protriat HP server. I need to set new password for ILO without installing any RPM like "hponfig".... I need to set password in terminal. please give me steps to change the password waiting for ur replys (1 Reply)
Discussion started by: suresh_krish
1 Replies

7. IP Networking

HP iLO using DHCP & Default Password

Hi, I have two questions about HP system iLO: (1) The <HP iLO 2 User Guide> says "Configure the IP address: This step is necessary only if you are using a static IP address. When using dynamic IP addressing, your DHCP server will automatically assign an IP address for iLO 2. HP recommends using... (6 Replies)
Discussion started by: aixlover
6 Replies

8. Shell Programming and Scripting

Hp ilo from Linux

Hi, I want to do momentary press to one server from linux is it possible? I got this command from internet is it correct? or need changes? I also need help how to start and reboot server in hp ilo from linux server. fence_ilo -a 10.1.41.155 -l Admin -p Password (1 Reply)
Discussion started by: learnbash
1 Replies

9. UNIX for Dummies Questions & Answers

HP DL380 G6 ILO question Linux

Hi, I have Redhat Linux 5.9. I need to connect all the ILO to different switch which can support 1 Gig. How can I find if ILO port can support gigabit? I am on HP website but not able to find anything about this information. Not sure I am looking in the correct place. Please help. (3 Replies)
Discussion started by: samnyc
3 Replies

10. HP-UX

Hp rx2620: is possible to access ILO via serial COM1?

Fast question: a bad reset put ilo ip to 127.0.0.1(!) and now i cannot reach via network Is possible to get ilo via serial using COM1/console? I see three console ports on server back side two are standard and one is reachable only with this cable... 403 Forbidden but i don't have this... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
FENCE_AGENT(8)						      System Manager's Manual						    FENCE_AGENT(8)

NAME
fence_ipmilan - Fence agent for IPMI over LAN fence_ilo3 - Fence agent for HP iLO3 (symlink) fence_ilo4 - Fence agent for HP iLO4 (symlink) fence_idrac - Fence agent for Dell iDRAC (symlink) fence_imm - Fence agent for IBM Integrated Management Module (symlink) DESCRIPTION
fence_ipmilan is an I/O Fencing agent which can be used with machines controlled by IPMI. This agent calls support software using ipmitool (http://ipmitool.sf.net/). To use fence_ipmilan with HP iLO 3 or HP iLO 4 you have to enable lanplus option (lanplus / -P) and increase wait after operation to 4 sec- onds (power_wait=4 / -T 4) fence_ipmilan accepts options on the command line as well as from stdin. Fenced sends parameters through stdin when it execs the agent. fence_ipmilan can be run by itself with command line options. This is useful for testing and for turning outlets on or off from scripts. Vendor URL: http://www.intel.com PARAMETERS
-A IPMI Lan Auth type (md5, password, or none) -a IPMI Lan IP to talk to This parameter is always required. -p Password (if required) to control power on IPMI device -S Script to retrieve password (if required) -P Use Lanplus to improve security of connection -l Username/Login (if required) to control power on IPMI device -o Operation to perform. Valid operations: on, off, reboot, status, list, diag, monitor or metadata (Default Value: reboot) -t Timeout (sec) for IPMI operation -C Ciphersuite to use (same as ipmitool -C parameter) -M Method to fence (onoff or cycle) (Default Value: onoff) -T Wait X seconds after on/off operation (Default Value: 2) -f Wait X seconds before fencing is started -L Privilege level on IPMI device -v Verbose mode ACTIONS
on Power on machine. off Power off machine. reboot Reboot machine. status This returns the status of the plug/virtual machine. diag The operational behavior of this is not known. list List available plugs with aliases/virtual machines if there is support for more then one device. Returns N/A otherwise. monitor Check the health of fence device metadata Display the XML metadata describing this resource. STDIN PARAMETERS
auth IPMI Lan Auth type (md5, password, or none) ipaddr IPMI Lan IP to talk to This parameter is always required. passwd Password (if required) to control power on IPMI device passwd_script Script to retrieve password (if required) lanplus Use Lanplus to improve security of connection login Username/Login (if required) to control power on IPMI device action Operation to perform. Valid operations: on, off, reboot, status, list, diag, monitor or metadata (Default Value: reboot) timeout Timeout (sec) for IPMI operation cipher Ciphersuite to use (same as ipmitool -C parameter) method Method to fence (onoff or cycle) (Default Value: onoff) power_wait Wait X seconds after on/off operation (Default Value: 2) delay Wait X seconds before fencing is started privlvl Privilege level on IPMI device verbose Verbose mode fence_ipmilan (Fence Agent) 2009-10-20 FENCE_AGENT(8)
All times are GMT -4. The time now is 08:57 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy