Sponsored Content
Full Discussion: iLO configuration
Operating Systems HP-UX iLO configuration Post 302397674 by sijocg on Tuesday 23rd of February 2010 12:25:01 AM
Old 02-23-2010
iLO configuration

how to set IP for iLO in HP server first time


thanks to all
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Xhost and ILO

I have an application that requires me to disable the restricted access to the X Server libraries by issuing the 'Xhost +' command from a Console Window. It is important that this command is run from the Console Window and not a Terminal Window otherwise the system complains that DISPLAY is not... (0 Replies)
Discussion started by: jimthompson
0 Replies

2. Solaris

HP iLO virtual serial port

Greetings All, If someone/anyone reading this post has had success setting up and configuring HP iLO2 CLI virtual serial port for Solaris...please tell how. I'm trying to get a remote console to an HP DL385 server via iLO2 and ssh. The server is running Solaris 10 (11/06), patched to... (1 Reply)
Discussion started by: alias.256
1 Replies

3. HP-UX

iLo RBSU

Hi, I wanted to setup a ilo for an HP 9000 rp 8420 server. Can anyone have an idea on it? (1 Reply)
Discussion started by: gunnervarma
1 Replies

4. Linux

Findout iLO type installed in a machine

I have to write Linux script to findout what kind of ilo is been installed in the given ip address either ilo/LO100 or no device found. IP address will be given in the command line of the script. -> With out log on to the ip address, should get the ilo type installed in that machine. 1. I... (1 Reply)
Discussion started by: skmdu
1 Replies

5. Solaris

T5220 ILO not saving static IP

I have a brand new T5220 and I'm trying to configure the ILOM port with a static Ip address via the Serial Management port. I log on as "root" and then enter the commands ( see below) to config the port. When I enter the last command which is " set /SP/network commitpending=true", which I... (9 Replies)
Discussion started by: danfall4
9 Replies

6. Hardware

Reset ILO password

HI Guys I have forgot my ILO password for REDHAT Linux, Its Protriat HP server. I need to set new password for ILO without installing any RPM like "hponfig".... I need to set password in terminal. please give me steps to change the password waiting for ur replys (1 Reply)
Discussion started by: suresh_krish
1 Replies

7. IP Networking

HP iLO using DHCP & Default Password

Hi, I have two questions about HP system iLO: (1) The <HP iLO 2 User Guide> says "Configure the IP address: This step is necessary only if you are using a static IP address. When using dynamic IP addressing, your DHCP server will automatically assign an IP address for iLO 2. HP recommends using... (6 Replies)
Discussion started by: aixlover
6 Replies

8. Shell Programming and Scripting

Hp ilo from Linux

Hi, I want to do momentary press to one server from linux is it possible? I got this command from internet is it correct? or need changes? I also need help how to start and reboot server in hp ilo from linux server. fence_ilo -a 10.1.41.155 -l Admin -p Password (1 Reply)
Discussion started by: learnbash
1 Replies

9. UNIX for Dummies Questions & Answers

HP DL380 G6 ILO question Linux

Hi, I have Redhat Linux 5.9. I need to connect all the ILO to different switch which can support 1 Gig. How can I find if ILO port can support gigabit? I am on HP website but not able to find anything about this information. Not sure I am looking in the correct place. Please help. (3 Replies)
Discussion started by: samnyc
3 Replies

10. HP-UX

Hp rx2620: is possible to access ILO via serial COM1?

Fast question: a bad reset put ilo ip to 127.0.0.1(!) and now i cannot reach via network Is possible to get ilo via serial using COM1/console? I see three console ports on server back side two are standard and one is reachable only with this cable... 403 Forbidden but i don't have this... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
CANNASTAT(1)						      General Commands Manual						      CANNASTAT(1)

NAME
cannastat - Display information about the Kana-Kanji conversion server SYNOPSIS
cannastat [{-cs|-cannaserver} canna-server ] [-p] [-t] [-a] DESCRIPTION
cannastat(1) displays information about the Kana-Kanji conversion server cannaserver(1M). The information includes the following: the name of the machine on which the connected server exists, the cannaserver(1M)'s version, the number of clients connecting to the server, the name of the user connecting to the server, its user number, the socket number, the number of contexts, the time of connection to the server, the time of use of the server, the idle time, the name of the host under which the client exists, and the frequency of using each protocol. If cannastat(1) is called without options, the following is displayed: Connected to machine1 Canna Server (Ver. 2.1) Total connecting clients 1 USER_NAME ID NO U_CX C_TIME U_TIME I_TIME HOST_NAME kon 5 0 4 Tue 21 8:49am 11 12:48 machine2 The items represent the following: USER_NAME User name ID Socket number NO User number U_CX Context number C_TIME Time of connection (h:min) U_TIME User time (h:min:s) I_TIME Idle time (h:min) HOST_NAME Name of the host under which the client exists OPTIONS
-cs canna-server (or -cannaserver canna-server) Specifies the Kana-Kanji conversion server. -p Displays the frequency of using the protocol. -t Displays information about the user who started cannastat. It includes the frequency of using the protocol, as well as ID, NO, U_CX, C_TIME, U_TIME, I_TIME, and HOST_NAME. -a Displays all information about all users. FILES
/etc/canna/cannahost Name of the host under which cannaserver is in operation. SEE ALSO
cannaserver(1M), cannakill(1M), cannacheck(1) ENVIRONMENT
CANNAHOST Specifies the name of the host under which cannaserver(1M) is in operation. CANNASTAT(1)
All times are GMT -4. The time now is 03:33 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy