Hello experts,
I have a series issue in script that result with bad peformence and I wonder if you can assist me.
For example
I have two files:
File-New, size 15Mb.
File-Old, size 1Mb.
File-New content:
a
b
c
k
File-Old content:
d
f
a
b (0 Replies)
Hi,
I am running a BASH shell with the following script. The script works and gives me correct output but is very slow with large files. The more rows and columns (width and height) the slower as you can probably see.
How can I do what I want more efficiently? Any ideas welcome. It has been... (10 Replies)
I had written a perl script to compare two files: new and master and get the output of the first file i.e. the first file: words that are not in the master file
STRUCTURE OF THE TWO FILES
The first file is a series of names
ramesh
sushil
jonga
sudesh
lugdi
whereas the second file (could be... (4 Replies)
My script builds a lot of these array lists, then compares their sizes which solves my problem, but runs very slow. :(
set -A comboSorted -- $(
for x in ${IDs}
do
nawk -v s=$x '
BEGIN { testPattern="^" s "$" }
{
if ( $2 ~ testPattern ) {
getline;getline;
if ($1 == "IMAGE_SIZE")
print... (1 Reply)
Basically my requirement is to know the total number of free anonymous ports.
anonymous port range is 32768- 65535.
i wrote a script for that
**********************************************
for i in {32768..65535}
do
netstat -an | grep $i > /dev/null
if
... (21 Replies)
Hi
I know the basic about script and sleep processes.
However this is more tricky:
I would like to run
sh -x /sbin/dhclient-script and slow down the output of the script as a whole.
How would you do it?
I would like to delay output on the screen with 1 second for every line for the output... (3 Replies)
I have shell program as below
#!/bin/sh
echo ======= LogManageri start ==========
#This directory is getting the raw data from remote server
Raw_data=/opt/ftplogs
# This directory is ready for process the data
Processing_dir=/opt/processing_dir
# This directory is prcoessed files and... (4 Replies)
Hello,
I am showing the start of my script.
I am finding that 'xmessage' is taking about 12-15 seconds to show.
This in a terminal is very quick '/opt/vc/bin/vcgencmd get_camera'.
Is there any way to get 'camera not detected' to show faster.
Regards
#!/bin/bash
s=$(/opt/vc/bin/vcgencmd... (4 Replies)
I'm new to utilities like socat and netcat and I'm not clear if they will do what I need.
I have a "compileDeployStartWebServer.sh" script and a "StartBrowser.sh" script that are started by emacs/elisp at the same time in two different processes.
I'm using Cygwin bash on Windows 10.
My... (3 Replies)
Discussion started by: siegfried
3 Replies
LEARN ABOUT DEBIAN
get-iab
GET-IAB(1) General Commands Manual GET-IAB(1)NAME
get-iab - Fetch the arp-scan IAB file from the IEEE website
SYNOPSIS
get-iab [options]
DESCRIPTION
get-iab fetches the Ethernet IAB file from the IEEE website, and saves it in the format used by arp-scan.
The IAB file contains all of the IABs (Individual Address Blocks) that have been registered with IEEE. Each IAB entry in the file speci-
fies the first 36-bits of the 48-bit Ethernet hardware address, leaving the remaining 12-bits for use by the registering organisation. For
example the IAB entry "0050C2003", registered to Microsoft, applies to any Ethernet hardware address from 00:50:c2:00:30:00 to
00:50:c2:00:3f:ff inclusive. Each IAB assignment represents a total of 2^12 (4,096) Ethernet addresses.
Major Ethernet hardware vendors typically use an OUI registration rather than an IAB registration. See get-oui(1) for details.
This script can be used to update the arp-scan IAB file from the latest data on the IEEE website. It is relatively rare to see Ethernet
addresses from IAB registrations, so the IAB file is not as important as the OUI file.
The IAB data is fetched from the URL http://standards.ieee.org/regauth/oui/iab.txt and the output file is saved to the file ieee-iab.txt in
the current directory. The URL to fetch the data from can be changed with the -u option, and the output file name can be changed with the
-f option.
The ieee-iab.txt file that is produced by this script is used by arp-scan to determine the Ethernet card vendor from its hardware address.
The directory that arp-scan will look for the ieee-iab.txt file depends on the options used when it was built. If it was built using the
default options, then it will look in /usr/local/share/arp-scan.
OPTIONS -h Display a brief usage message and exit.
-f <fn>
Write the output to the specified file instead of the default ieee-iab.txt.
-u <URL>
Use the specified URL to fetch the raw IAB data from instead of the default http://standards.ieee.org/regauth/oui/iab.txt
-v Display verbose progress messages.
FILES
ieee-iab.txt
The default output file.
EXAMPLES
$ get-iab -v
Renaming ieee-iab.txt to ieee-iab.txt.bak
Fetching IAB data from http://standards.ieee.org/regauth/oui/iab.txt
Fetched 230786 bytes
Opening output file ieee-iab.txt
1535 IAB entries written to file ieee-iab.txt
NOTES
get-iab is implemented in Perl, so you need to have the Perl interpreter installed on your system to use it.
get-iab uses the LWP::Simple Perl module to fetch the data from the IEEE website. You must have this module installed on your system for it
to work. This module is available on most distributions, often called libwww-perl. It is also available in source form from CPAN.
You can use a proxy server by defining the http_proxy environment variable.
AUTHOR
Roy Hills <Roy.Hills@nta-monitor.com>
SEE ALSO arp-scan(1)get-oui(1)arp-fingerprint(1)
http://www.nta-monitor.com/wiki/ The arp-scan wiki page.
March 30, 2007 GET-IAB(1)