Sponsored Content
Operating Systems SCO Problems with network card in SCO Post 302381304 by daniel_cie on Thursday 17th of December 2009 07:42:21 PM
Old 12-17-2009
hello, I already have the values:
Bus: 0
Device: 8
Function: 0
apply changes in netconfig, but when I press exit netconfig, press "YES" in Relinked Kernel, and displays the message:

Error: Cannot find Driver.o for sem.
Fatal Error: Erros encountered. Configuration Terminated.
idbuild: idconfig had errors
system build failed

restart the server, but the changes did not work.
in /usr/adm/messages shows the same as before:
ktcHT 0xd400-0xd41f - - Kingston Et ....... NOT FOUND [KNE120TX]
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

3. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

5. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

8. SCO

network problems with sco

SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that. thanks (8 Replies)
Discussion started by: ajantha
8 Replies

9. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
CFREE(3)						     Linux Programmer's Manual							  CFREE(3)

NAME
cfree - free allocated memory SYNOPSIS
#include <stdlib.h> /* In SunOS 4 */ int cfree(void *ptr); /* In glibc or FreeBSD libcompat */ void cfree(void *ptr); /* In SCO OpenServer */ void cfree(char *ptr, unsigned num, unsigned size); /* In Solaris watchmalloc.so.1 */ void cfree(void *ptr, size_t nelem, size_t elsize); Feature Test Macro Requirements for glibc (see feature_test_macros(7)): cfree(): _BSD_SOURCE || _SVID_SOURCE DESCRIPTION
This function should never be used. Use free(3) instead. 1-arg cfree In glibc, the function cfree() is a synonym for free(3), "added for compatibility with SunOS". Other systems have other functions with this name. The declaration is sometimes in <stdlib.h> and sometimes in <malloc.h>. 3-arg cfree Some SCO and Solaris versions have malloc libraries with a 3-argument cfree(), apparently as an analog to calloc(3). If you need it while porting something, add #define cfree(p, n, s) free((p)) to your file. A frequently asked question is "Can I use free(3) to free memory allocated with calloc(3), or do I need cfree()?" Answer: use free(3). An SCO manual writes: "The cfree routine is provided for compliance to the iBCSe2 standard and simply calls free. The num and size argu- ments to cfree are not used." RETURN VALUE
The SunOS version of cfree() (which is a synonym for free(3)) returns 1 on success and 0 on failure. In case of error, errno is set to EINVAL: the value of ptr was not a pointer to a block previously allocated by one of the routines in the malloc(3) family. CONFORMING TO
The 3-argument version of cfree() as used by SCO conforms to the iBCSe2 standard: Intel386 Binary Compatibility Specification, Edition 2. SEE ALSO
malloc(3) COLOPHON
This page is part of release 3.25 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. 2007-07-26 CFREE(3)
All times are GMT -4. The time now is 02:38 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy