Sponsored Content
Operating Systems SCO Problems with network card in SCO Post 302381219 by jgt on Thursday 17th of December 2009 01:29:33 PM
Old 12-17-2009
Quote:
Bus = 0
Device = 0
Function = 0


I did a check of a system running XP Pro.
The three values show in the network connections -->configure card window.
So a convoluted way to find out would be to temporarily replace the disk, and install XP then look at the network connection info.
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

3. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

5. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

8. SCO

network problems with sco

SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that. thanks (8 Replies)
Discussion started by: ajantha
8 Replies

9. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
merge_fonts(3alleg4)						  Allegro manual					      merge_fonts(3alleg4)

NAME
merge_fonts - Merges two fonts into one font. Allegro game programming library. SYNOPSIS
#include <allegro.h> FONT *merge_fonts(FONT *f1, FONT *f2) DESCRIPTION
This function merges the character ranges from two fonts and returns a new font containing all characters in the old fonts. In general, you cannot merge fonts of different types (eg, TrueType fonts and bitmapped fonts), but as a special case, this function can promote a mono- chrome bitmapped font to a color font and merge those. Example: FONT *myfont; FONT *myfancy_font; FONT *lower_range; FONT *upper_range; FONT *capitals; FONT *combined_font; FONT *tempfont; ... /* Create a font that contains the capitals from */ /* the fancy font but other characters from myfont */ lower_range = extract_font_range(myfont, -1, 'A'-1); upper_range = extract_font_range(myfont, 'Z'+1, -1); capitals = extract_font_range(myfancy_font, 'A', 'Z'); tempfont = merge_fonts(lower_range, capitals); combined_font = merge_fonts(tempfont, upper_range); /* Clean up temporary fonts */ destroy_font(lower_range); destroy_font(upper_range); destroy_font(capitals); destroy_font(tempfont); RETURN VALUE
Returns a pointer to the new font or NULL on error. Remember that you are responsible for destroying the font when you are finished with it to avoid memory leaks. SEE ALSO
extract_font_range(3alleg4), is_trans_font(3alleg4), is_color_font(3alleg4), is_mono_font(3alleg4), exfont(3alleg4) Allegro version 4.4.2 merge_fonts(3alleg4)
All times are GMT -4. The time now is 03:21 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy