12-16-2009
The "correct" values will vary based upon the motherboard, and the slot that the card is installed in.
When the system does its POST (power on self test) you may, depending on which brand of BIOS you have, see a list of all the PCI interfaces in the system and three columns of values to the right side of the screen. These three columns represent the three values that you need.
If the screen scrolls past too quickly to see, change the boot sequence to diskette, or cd only and put a blank diskette/cd in the appropriate drive; the system will stop with "NO OS found" and allow you to read the POST data.
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
3. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. SCO
Hi,
I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. SCO
SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that.
thanks (8 Replies)
Discussion started by: ajantha
8 Replies
9. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT FREEBSD
hv_netvsc
HYPER-V(4) BSD Kernel Interfaces Manual HYPER-V(4)
NAME
hv_netvsc -- Hyper-V Network Virtual Service Consumer
SYNOPSIS
To compile this driver into the kernel, place the following lines in the system kernel configuration file:
device hyperv
DESCRIPTION
The hv_netvsc driver implements the virtual network device for FreeBSD guest partitions running on Hyper-V. FreeBSD guest partitions running
on Hyper-V do not have direct access to network devices attached to the Hyper-V server. Although a FreeBSD guest can access network devices
using Hyper-V's full emulation mode, the performance in this mode tends to be unsatisfactory.
To counter the above issues, the hv_netvsc driver implements a network Virtual Service Consumer (VSC) that relays network requests from the
guest partition to the network Virtual Service Provider (VSP) hosted in the root partition using the high performance data exchange infra-
structure provided by hv_vmbus(4) driver. The VSP in the root partition then forwards the network related requests to the physical network
card.
SEE ALSO
hv_ata_pci_disengage(4), hv_storvsc(4), hv_utils(4), hv_vmbus(4)
HISTORY
Support for hv_netvsc first appeared in FreeBSD 10.0. The driver was developed through a joint effort between Citrix Incorporated, Microsoft
Corporation, and Network Appliance Incorporated.
AUTHORS
FreeBSD support for hv_netvsc was first added by Microsoft BSD Integration Services Team <bsdic@microsoft.com>.
BSD
September 10, 2013 BSD