|
|
Sponsored Content
Operating Systems
SCO
Warning HD: no root disk controller was found
Post 302358892 by mselvaprakash on Monday 5th of October 2009 07:24:16 AM
10-05-2009
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. Solaris
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Discussion started by: sunnyd76
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT XFREE86
bootctl
BOOTCTL(1) bootctl BOOTCTL(1) NAME
bootctl - Control the firmware and boot manager settings SYNOPSIS
bootctl [OPTIONS...] status bootctl [OPTIONS...] list bootctl [OPTIONS...] update bootctl [OPTIONS...] install bootctl [OPTIONS...] remove DESCRIPTION
bootctl checks, updates, installs or removes the boot loader from the current system. bootctl status checks and prints the currently installed versions of the boot loader binaries and all current EFI boot variables. bootctl list displays all configured boot loader entries. bootctl update updates all installed versions of systemd-boot, if the current version is newer than the version installed in the EFI system partition. This also includes the EFI default/fallback loader at /EFI/BOOT/BOOT*.EFI. A systemd-boot entry in the EFI boot variables is created if there is no current entry. The created entry will be added to the end of the boot order list. bootctl install installs systemd-boot into the EFI system partition. A copy of systemd-boot will be stored as the EFI default/fallback loader at /EFI/BOOT/BOOT*.EFI. A systemd-boot entry in the EFI boot variables is created and added to the top of the boot order list. bootctl remove removes all installed versions of systemd-boot from the EFI system partition, and removes systemd-boot from the EFI boot variables. If no command is passed, status is implied. OPTIONS
The following options are understood: -h, --help Print a short help text and exit. --version Print a short version string and exit. --path= Path to the EFI System Partition (ESP). If not specified, /efi, /boot, and /boot/efi are checked in turn. It is recommended to mount the ESP to /boot, if possible. -p, --print-path This option modifies the behaviour of status. Just print the path to the EFI System Partition (ESP) to standard output and exit. --no-variables Do not touch the EFI boot variables. EXIT STATUS
On success, 0 is returned, a non-zero failure code otherwise. SEE ALSO
Boot loader specification[1] systemd boot loader interface[2] NOTES
1. Boot loader specification https://www.freedesktop.org/wiki/Specifications/BootLoaderSpec 2. systemd boot loader interface https://www.freedesktop.org/wiki/Software/systemd/BootLoaderInterface systemd 237 BOOTCTL(1)