TCPREPLAY(1)							Programmer's Manual						      TCPREPLAY(1)

NAME

       tcpreplay - Replay network traffic stored in pcap files

SYNOPSIS

       tcpreplay [-flag [value]]... [--opt-name [[=| ]value]]...
	       <pcap_file(s)>

       tcpreplay is a tool for replaying network traffic from files saved with tcpdump or other tools which write pcap(3) files.

DESCRIPTION

       This  manual  page  briefly  documents the tcpreplay command.  The basic operation of tcpreplay is to resend  all  packets  from  the input
       file(s) at the speed at which they were recorded, or a specified data rate, up to as fast as the hardware is capable.

       Optionally, the traffic can be split between two interfaces, written to files, filtered and edited in various ways, providing the means	to
       test firewalls, NIDS and other network devices.

       For more details, please see the Tcpreplay Manual at: http://tcpreplay.synfin.net/trac/wiki/manual

OPTIONS

       -d number, --dbug=number
	      Enable  debugging output.  This option may appear up to 1 times.	This option takes an integer number as its argument.  The value of
	      number is constrained to being:
		  in the range	0 through 5
	      The default number for this option is:
		   0

	      If configured with --enable-debug, then you can specify a verbosity level for debugging output.  Higher numbers increase verbosity.

       -q, --quiet
	      Quiet mode.

	      Print nothing except the statistics at the end of the run

       -T string, --timer=string
	      Select packet timing mode: select, ioport, rdtsc, gtod, nano, abstime.  This option may appear up to 1 times.  The default string
	      for this option is:
		   gtod

	      Allows you to select the packet timing method to use:

	      nano - Use nanosleep() API

	      select - Use select() API

	      ioport - Write to the i386 IO Port 0x80

	      rdtsc - Use the x86/x86_64/PPC RDTSC

	      gtod [default] - Use a gettimeofday() loop

	      abstime - Use OS X's AbsoluteTime API

       --sleep-accel=number
	      Reduce the amount of time to sleep by specified usec.  This option takes an integer number as its argument.  The default number for
	      this option is:
		   0

	      Reduce the amount of time we would normally sleep between two packets by the specified number of usec.  This provides a "fuzz fac-
	      tor" to compensate for running on a non-RTOS and other processes using CPU time.	Default is disabled.

       --rdtsc-clicks=number
	      Specify the RDTSC clicks/usec.  This option may appear up to 1 times.  This option takes an integer number as its argument.  The
	      default number for this option is:
		   0

	      Override the calculated number of RDTSC clicks/usec which is often the speed of the CPU in Mhz.  Only useful if you specified
	      --timer=rdtsc

       -v, --verbose
	      Print decoded packets via tcpdump to STDOUT.  This option may appear up to 1 times.

       -A string, --decode=string
	      Arguments passed to tcpdump decoder.  This option may appear up to 1 times.  This option must appear in combination with the follow-
	      ing options: verbose.

	      When enabling verbose mode (-v) you may also specify one or more additional  arguments to pass to tcpdump to modify the way packets
	      are decoded.  By default, -n and -l are used.   Be  sure	to quote the arguments like: -A "-axxx" so that they are not interpreted
	      by tcpreplay.   Please see the tcpdump(1) man page for a complete list of options.

       -K, --enable-file-cache
	      Enable caching of packets to internal memory.  This option must appear in combination with the following options: loop.

	      Cache pcap file(s) the first time they are cached in RAM so that subsequent loops don't incurr any disk I/O latency in order to
	      increase performance.  Make sure you have enough free RAM to store the entire pcap file(s) in memory or the system will swap and
	      performance will suffer.

       -c string, --cachefile=string
	      Split traffic via a tcpprep cache file.  This option may appear up to 1 times.

       -i string, --intf1=string
	      Server/primary traffic output interface.	This option may appear up to 1 times.

       -I string, --intf2=string
	      Client/secondary traffic output interface.  This option may appear up to 1 times.  This option must appear in combination with the
	      following options: cachefile.

       --listnics
	      List available network interfaces and exit.

       -l number, --loop=number
	      Loop through the capture file X times.  This option may appear up to 1 times.  This option takes an integer number as its argument.
	      The value of number is constrained to being:
		  greater than or equal to 0
	      The default number for this option is:
		   1

       --pktlen
	      Override the snaplen and use the actual packet len.  This option may appear up to 1 times.

	      By default, tcpreplay will send packets based on the size of the "snaplen" stored in the pcap file which is usually the correct
	      thing to do.  However, occasionally, tools will store more bytes then told to.  By specifying this option, tcpreplay will ignore the
	      snaplen field and instead try to send packets based on the original packet length.  Bad things may happen if you specify this
	      option.

       -L number, --limit=number
	      Limit the number of packets to send.  This option may appear up to 1 times.  This option takes an integer number as its argument.
	      The value of number is constrained to being:
		  greater than or equal to 1
	      The default number for this option is:
		   -1

	      By default, tcpreplay will send all the packets.	Alternatively, you can specify a maximum number of packets to send.

       -x string, --multiplier=string
	      Modify replay speed to a given multiple.	This option may appear up to 1 times.  This option must not appear in combination with any
	      of the following options: pps, mbps, oneatatime, topspeed.

	      Specify a floating point value to modify the packet replay speed.  Examples:
		      2.0 will replay traffic at twice the speed captured
		      0.7 will replay traffic at 70% the speed captured

       -p number, --pps=number
	      Replay packets at a given packets/sec.  This option may appear up to 1 times.  This option must not appear in combination with any
	      of the following options: multiplier, mbps, oneatatime, topspeed.  This option takes an integer number as its argument.

       -M string, --mbps=string
	      Replay packets at a given Mbps.  This option may appear up to 1 times.  This option must not appear in combination with any of the
	      following options: multiplier, pps, oneatatime, topspeed.

	      Specify a floating point value for the Mbps rate that tcpreplay should send packets at.

       -t, --topspeed
	      Replay packets as fast as possible.  This option must not appear in combination with any of the following options: mbps, multiplier,
	      pps, oneatatime.

       -o, --oneatatime
	      Replay one packet at a time for each user input.	This option must not appear in combination with any of the following options:
	      mbps, pps, multiplier, topspeed.

	      Allows you to step through one or more packets at a time.

       --pps-multi=number
	      Number of packets to send for each time interval.  This option must appear in combination with the following options: pps.  This
	      option takes an integer number as its argument.  The value of number is constrained to being:
		  greater than or equal to 1
	      The default number for this option is:
		   1

	      When trying to send packets at very high rates, the time between each packet can be so short that it is impossible to accurately
	      sleep for the required period of time.  This option allows you to send multiple packets at a time, thus allowing for longer sleep
	      times which can be more accurately implemented.

       -P, --pid
	      Print the PID of tcpreplay at startup.

       -V, --version
	      Print version information.

       -h, --less-help
	      Display less usage information and exit.

       -H, --help
	      Display usage information and exit.

       -!, --more-help
	      Extended usage information passed thru pager.

       - [rcfile], --save-opts[=rcfile]
	      Save the option state to rcfile.	The default is the last configuration file listed in the OPTION PRESETS section, below.

       - rcfile, --load-opts=rcfile, --no-load-opts
	      Load options from rcfile.  The no-load-opts form will disable the loading of earlier RC/INI files.  --no-load-opts is handled early,
	      out of order.

OPTION PRESETS

       Any option that is not marked as not presettable may be preset by loading values from configuration ("RC" or ".INI") file(s).  The homerc
       file is "$$/", unless that is a directory.  In that case, the file ".tcpreplayrc" is searched for within that directory.

SIGNALS

       tcpreplay understands the following signals:

       SIGUSR1 Suspend tcpreplay

       SIGCONT Restart tcpreplay

SEE ALSO

       tcpreplay-edit(1), tcpdump(1), tcpprep(1), tcprewrite(1), libnet(3)

BUGS

       tcpreplay can only send packets as fast as your computer's interface, processor, disk and system bus will allow.

       Packet timing at high speeds is a black art and very OS/CPU dependent.

       Replaying captured traffic may simulate odd or broken conditions on your network and cause all sorts of problems.

       In most cases, you can not replay traffic back to/at a server.

       Some operating systems by default do not allow for forging source MAC addresses.  Please consult your operating system's documentation and
       the tcpreplay FAQ if you experience this issue.

AUTHOR

       Copyright 2000-2008 Aaron Turner

       For support please use the tcpreplay-users@lists.sourceforge.net mailing list.

       The latest version of this software is always available from: http://tcpreplay.synfin.net/

       Released under the Free BSD License.

       This manual page was AutoGen-erated from the tcpreplay option definitions.

(tcpreplay )							    2009-06-25							      TCPREPLAY(1)