|
|
Sponsored Content
Operating Systems
Solaris
Setting up static ip-adresses, Solaris 10
Post 302173873 by empty on Saturday 8th of March 2008 04:44:05 PM
03-08-2008
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hi All, :(:confused:
I have scoured the web and can't find this anywhere.
What I am trying to do is set up a static route through an available gateway on a server, and then test connectivity through TELNET.
I have done this on AIX (I already had this procedure).
On AIX I would use SMIT. ... (7 Replies)
Discussion started by: jeffpas
7 Replies
2. IP Networking
hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first.
... (0 Replies)
Discussion started by: dlwoaud
0 Replies
3. UNIX for Dummies Questions & Answers
Hi All
I am having a solaris 10 virtual machine on vista (using vmware 7) laptop.
Now i want to access virtual machine from vista using putty.
Problem is that i insalled the solaris machine as dhcp. and whenever i connect to internet or reboot my system the IP address of solaris... (1 Reply)
Discussion started by: ankurk
1 Replies
4. Solaris
Hi,
I have cloned a SOLARIS 8 (BLADE 150) Hard Disk and have put into other system. So, now how do I configure the NIC and assign static IP for this new machine ? (8 Replies)
Discussion started by: angshuman_ag
8 Replies
5. Solaris
hi,
how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc.. (2 Replies)
Discussion started by: pankajd
2 Replies
6. IP Networking
I have been trying to setup a static ip, however everytime I do so my internet disconnects and won't connect untill I switch back to dynamic. My router is a NetGear DGN1000 and I'm using it wired. Could anyone help? (0 Replies)
Discussion started by: zomigosh
0 Replies
7. Solaris
hi guys
How to know ILOM and ALOM ip address.
how to find the ilom alerts and alom alerts can one help out pls
thanks,
deepu.
---------- Post updated at 04:39 AM ---------- Previous update was at 04:38 AM ---------- (2 Replies)
Discussion started by: pradeepaasuri
2 Replies
8. Red Hat
Hi Guys,
I want to some guidance from you in setting up the Live FTP server in Redhat Linux 6 with Static IP
120.50.150.50.
Now should I set my Static Public IP directly to my Linux machine?
If so what whould be my sunbet mask?
Is any type of natting required here? if so where would... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
9. Solaris
I have installed Solaris 11.2 in VMware Player, networked in bridged mode. When Solaris uses DHCP everything is OK, I can reach internet, as well as other systems on my LAN. When I switch to static, I have connections to my LAN, but can not get to internet, the DNS resolution is somehow not... (2 Replies)
Discussion started by: migurus
2 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
LEARN ABOUT MINIX
ifconfig
IFCONFIG(8) System Manager's Manual IFCONFIG(8) NAME
ifconfig - configure a TCP/IP device SYNOPSIS
ifconfig [-I ip-device] [-h ipaddr] [-n netmask] [-iv] DESCRIPTION
Ifconfig initializes a TCP/IP device setting the IP address and/or netmask. It will report the address and netmask set. This command may be used if the system has not been configured properly yet. It is only used at boot time to set a fixed address for a system without a physical ethernet. Normally the inet task will find it out by itself from the RARP server. OPTIONS
-h The decimal TCP/IP address to set. -n The netmask to set. -i Don't set the IP address or netmask if already set. This way ifconfig cannot interfere if the numbers have been found out by RARP. -v Report IP address and netmask. This is the default action if there are no other options. SEE ALSO
hostaddr(1), rarpd(8), set_net_default(8), boot(8). AUTHOR
Kees J. Bot (kjb@cs.vu.nl) IFCONFIG(8)